The Canon LC-E19 Battery Charger for Camerasfrom Canon LC-E19 Battery Charger for Cameraswill charge two separate LP-E19, LP-E4, or LP-E4N battery packs. LP-E19 batteries charge at a rate of 170 minutes per battery, while LP-E4 and LP-E4N charge at a rate of 140 minutes per battery. It plugs directly into AC outlets and includes an AC adapter.

For LP-E19, LP-E4, and LP-E4N Batteries    LP-E19 Batteries Charged in 170 Minutes    LP-E4/LP-E4N Charged in 140 Minutes    Plugs Directly into AC Outlets

Related Questions and Answers

Q: 1. Can I use power supply to power up the camera for continous recording video?

A: There is an AC adapter setup but no External battery option we are aware of. The AC option is two parts. 1. Canon DR-E19 DC Coupler BH #CADRE19 • MFR #1172C001 https://bhpho.to/31mB5vU 2. Canon AC Adapter AC-E19 BH #CAACE19 • MFR #1171C002 https://bhpho.to/2SgDDaz

Q: 2. Is there any way to replace the black cap ?

A: Unfortunately no, this would have to be repaired or replaced by Canon or an Authorized Canon Repair Facility.

Q: 3. Can this battery be used in a Canon 1DsIII?

A: Canon currently lists the current generation of 1D-cameras (1Dx Mk III) as being the only camera compatible with the LP-E19. However, the LP-E4, LP-E4N, and LP-E19 share the same physical dimensions/configuration and likely this battery will be compatible with the 1Ds Mk III, but we currently have no way of confirming.

Q: 4. Will the LP-E19 battery work with the R5 or R6 using the battery grip in place of the dual batter tray?

A: No. Cannon R5 use the following battery Canon LP-E6NH Lithium-Ion Battery (7.2V, 2130mAh) BH #CALPE6NH • MFR #4132C002 https://bhpho.to/3GWNpax

Q: 5. My LP-E19 battery self -discharge when left in my 1DXII .It happens after I calibrated it before recharging. Is there a way to reverse it?

A: According to Canon, the charger will fully deplete the LP-E19 then fully charge it when utilizing the calibration process. This process can take about 18-19 hours to complete and should only be performed with an almost exhausted battery.

Q: 6. Does this work with the C500 Mark 2?

A: Yes, this is compatible with the C500 Mark II.

Q: 7. Do I need to buy any additional accessories for this to work with a Canon C500 Mark II or a Canon C300 Mark III or will this work out of the box?

A: No, it connects directly to those cameras.

Q: 8. Can you power the Anton/Bauer P-Tap to LP-E19 Regulated 10.8V Dummy Battery for Canon 1DX/1DX Mark II with a Bolt cyclone/DR PP-400DR

A: No, you cannot power the Anton/Bauer P-Tap to LP-E19 Regulated 10.8V Dummy Battery for Canon 1DX/1DX Mark II with any power accessory that doesn't have a D-Tap.

Q: 9. It looks like the same form factor as my 1D mark iii, mark iv, and X batteries. Will my existing batteries still work?

A: (cross posting). The batteries are interchangeable. The LP-E4 and LP-E19 have the same form factor and contacts. The LP-E4 will work in the 1DX Mark II at reduced camera performance. You can use the LP-E19 backward to the 1D Mark III but to get full battery performance you need the new charger. Otherwise the old charger will only charge to the performance level of the LP-E4 that it was designed for. Read about it by searching for canon lp-e19 charging with old charger that will go to the Canon learning article.

Q: 10. Will it fit in EOS R3?

A: Yes this battery is compatible with the EOS R3.