The 3/8"-16 Thread-On Quick Mount Receiverfrom 3/8"-16 Thread-On Quick Mount Receiverlets you add a Quick Mount Receiver to equipment that has a 3/8"-16 male thread, including 9.Solutions 3/8" rods. This enables you to attach a variety of Quick Mount accessories, such as 1/4"-20 and 3-Prong GoPro camera mounts.

3/8"-16 Thread-On Quick Mount ReceiverPlease be sure to always secure the unit using a separately-available 3/8" finger nut.

Accepts Quick Mount Accessories    Attaches to 3/8"-16 Male Threading

Related Questions and Answers

Q: 1. If the Tx is fed signal via HDMI, will the local BNC loop thru / output transcode that signal lien the older 500 units did?

A: Yes, the Teradek Bolt 6 LT 750 3G-SDI/HDMI Wireless Transmitter supports HDMI cross conversion. This would allow the HDMI input to output through the 3G-SDI. The Teradek Bolt 6 also would downscale 4k signals from HDMI to HD when outputting via the 3D-SDI.

Q: 2. I have a set of Photogenic strobes (from the early '90's). Will this work with Photogenic strobe models from that time frame?

A: If your Photogenic strobes use the standard IEC power cable and has either a 1/8 (3.5mm) miniphone sync terminal or 1/4 headphone sync terminal, then yes, the Impact PowerTrigger 16 Channel AC Transmitter and Receiver Set would be compatible for use with your strobe units.

Q: 3. hi I just bought this trigger ( impact power trigger) and is not working... I have a canon 6d and have put the transmitter on the hot shoe of the camera and the red light has not light up even though i tried the 16 channels. the equipment is new so I may say the battery is new too... the connection in the impact vsd 160 monolight is ok... could it be a problem on the camera? I also have trouble shooting with the original sync cord that came with the monolight... please any indications will help. Thanks

A: I had the same difficulties with my trigger. I sent it back to the manufacturer and they said they could not find anything wrong with it. I did try I few things to troubleshoot it including the battery but it still didnt work. Impact said they would ask B&H to refund me.

Q: 4. Can anyone tell me the thickness of this plate?

A: 0.4 thickness

Q: 5. I purchased the 3 light kit and two additional transmitter and receiver sets. I noticed that when I use the test button, both strobes fire off fine, but when taking photographs, sometimes one of the lights will not trigger. Is anyone aware of similar issues? Using a Nikon D7100.

A: Always have backup batteries for this product because it can go at anytime. Agreed with other answer to switch up the battery and check the channel used. Also, might sound silly but make sure your wire connections/plug ins are all secure, nothing loose or adapters not fitting properly.

Q: 6. Will this work for sony a7III ?

A: No, Sony uses a multi interface system for the shoe and remote. Click the link below to view; https://bhpho.to/2ED0aLJ

Q: 7. Does the on camera transmitter have an off switch or does it not consume battery when not in use?

A: No, the following unit does not offer a on/ off switch.

Q: 8. Will this trigger more than one flash unit or do two receivers need to be purchased?

A: A receiver for each flash/strobe needs to be purchased.

Q: 9. Hi I'm not able yo use this... i have a canon 6D everything is plug well I have the trigger mount in the hot shoe of the camera but every time I press the shutter the light won't pop put if I press the test buttom it works perfectly. Batteries are ok I thinks is a problem between the camera and the trigger.. Any ideas? Also imposible to use the sync cord because i can not press the shutter it looks like it freeze. Thank you!

A: Received it today. It is not working on my Westcott Stroblite Plus. Won't work on the camera, and won't trigger the monolight with the text button. Tried all 16 channels. Any suggestions???

Q: 10. I have an old impact T-616 receiver. Will it work with this new model transmitter?

A: No. This is not backward compatible.