Finish your installation with a clean look with the black Whirlwind WP1B/2QW 1-Gang Wall Plate. It features a single-gang design with two Whirlwind WCQF 1/4" terminals to pass your wiring through the wall, reducing the appearance of cable clutter.

2x Whirlwind WCQF 1/4" Terminals    1-Gang Design

Related Questions and Answers

Q: 1. Will this hold a Canon 5D Mk IV, and if so, is a camera mount of some sort needed, or can the camera mount directly to this as is?

A: The Manfrotto 098B Wall Mounting Boom Arm, Black - 47.2-82.6" (1.2-2.1m) has a maximum load capacity of 9.92 lb (4.5 kg) at maximum extension. It will depend on the combined weight of your Canon EOS 5D Mark IV DSLR Camera (Body Only), which weighs 1.76 lb (800 g), and the lens you will be using on the camera body. I would recommend purchasing a ball head adapter such as the Impact LS-BHA Baby Ball Head Adapter, B&H # IMLSBHA, along with a ball head such as the Ulanzi U-80L Side Cold Shoe Mount Ball Head with Arca-Type Quick Release, B&H # ULU80L.

Q: 2. How do I move the locating pins from the horizontal to vertical position? I’ve tried pulling them out with pliers with no luck.

A: You could use Needle nose pliers would allow you to remove the screws. The pins unscrew like normal screws.

Q: 3. Can I buy/order one of these with a 3/8" screw?

A: The Really Right Stuff B22 Multiuse Fore-Aft Plate with 3/8"-16 Screw is Arca-Type Compatible. This plate will fit the same tripods as the MeFOTO RoadTrip and GlobeTrotter Air Quick Release Plate. Here is the link: https://bhpho.to/3At93jr

Q: 4. Is this compatible with MeFoto Backpacker S?

A: Yes. Both this and the ballhead on the Backpacker S employ the arca-swiss style.

Q: 5. Can you use Sennheiser Headphone with boom mic's (Headset) with this machine? is it for one microphone set up only (i.e only one commentator)do you have Australian power plugs for these

A: Yes the THS4 with work with Sennheiser Headsets. It has one mic/headset input.We do not supply Australian power plugs, one can either use an adapter or find their own wall supply that has a 12 V AC 1 Amp output. See our website at a href= http://www.whirlwindusa.com target= _blank www.whirlwindusa.com/a to learn more and download the product manual.

Q: 6. What size are the DC output pins?

A: The barrel sizes for the Tilta L-Series Battery Plate outputs are DC 5.5 X 2.5mm, which will fit in the 12V DC, and the DC 5.5 x 2.1mm, which will fit in the 8V DC.  One is DC 12V:DC55-25:5.5-2.5mm, One is DC 8V:DC5521:5.5-2.1mm.

Q: 7. Is this compatible with the fx3 tilta cage?

A: No, the Tilta Bottom Plate for Sony a7S III Cages (Black) will not work with Tilta FX3 cages.

Q: 8. What is the distance between the mounting screws?

A: That information is not listed because this provides the correct mounting hole placement for Tilta A7SIII cages specifically. If you have such a cage, this product will work with it.

Q: 9. Does this have an on and off master switch?

A: No, the Tilta PD V-Mount Battery Plate (Black) does not have an on/off switch.

Q: 10. Does this unit require external power? if so, how much and on what kind of connector?

A: The Whirlwind Line Balancer/Splitter requires no external power and is designed to split a single line level input signal into two balanced line level outputs. A choice of two output configurations is provided: one direct output and one isolated output, or two isolated outputs. The Line Balancer/ Splitter uses Whirlwinds TRSP-600L transformer and has a frequency response of 20 to 20kHz, 1dB @ +2OdBm.On the Line Balancer/Splitter are two male XLR jacks, one female XLR jack, a 14 jack and three switches as outlined below:INPUTEither of the two input connectors, a female XLR jack or a 14 TRS jack (Tip = Pin 2 and Ring = Pin 3) can be used for connection from a line level source, balanced or unbalanced. Use only one input at a time.OUTPUTSThe male XLR output connectors can be configured in one of two ways. The ISOLATED OUT/SPLIT 1 is always transformer isolated and the DIRECT OUT/SPLIT 2 is either directly connected to the input or transformer isolated, depending on the position of the OUTPUT SELECT switch.OUTPUT SELECTThis push-button switch selects the output mode of the unit. In the out position, the DIRECT OUT/SPLIT 2 provides a direct output signal and the ISOLATED OUT/SPLIT 1 provides a balanced 600 isolated signal. In the in position (the center of the switch changes to orange) both output connectors provide a balanced 150 ?isolated signal that is attenuated by 6dB from the input.GND/LIFTSEach of these switches disconnects the ground between the inputs and the XLR outputs when set to the LIFT position. Grounds remain connected when set to the GND position.This product is warranted to be free of defects in materials or workmanship to the original purchaser for a period of 3 years from the date of purchase.