Finish your installation with a clean look with the stainless steel Whirlwind WP2/2FW 2-Gang Wall Plate. It features a two-gang design with two Whirlwind WC3F female XLR terminals to pass your wiring through the wall, reducing the appearance of cable clutter.

2x Whirlwind WC3F Female XLR Terminals    2-Gang Design

Related Questions and Answers

Q: 1. For the metal chain, there are no instructions as to how to put it on the drive, as there are for the plastic ones. The plastic ones come opened up so they can be closed after threading. All I can figure out is that the varidrive has to be dissassembled to install the chain, Is that correct?

A: Yes, the black knobs unscrew allowing access for the chain to the gear.

Q: 2. I have a 95 and 3/4 inch wall and want to mount an 86” roll. Will it fit with the varidrive ends, cardboard core and brackets? I know it is very tight, any way to fit it though?

A: No, you will not have room to install the Impact Varidrive system on a 95 3/4’’ wall.

Q: 3. I'm using 9ft Savage backdrops. What should the distance of the hooks be so that the Varidrive Inserts groove fits the hooks?

A: The distance at which the hooks should be placed would depend on the distance of the studs behind the wall as much as the width of the paper.

Q: 4. How do I stop the background from unrolling completely?

A: You have to tighten the tension on the handles. It took me a while to figure it out.

Q: 5. Will this fit on the C400?

A: Yes, the Core SWX Battery Plate for Canon EOS Cine Cameras with 4-Pin XLR Input (V-Mount) is compatible with the Canon EOS C400 6K Full-Frame Digital Cinema Camera (Canon RF).

Q: 6. I'll be using this kit with 86-inch wide seamless paper (about 6 lbs per roll). I've read that one should remove the rolls after each use to prevent sagging in the middle and then issues unrolling/rolling. Have others found that to be the case? I was hoping I could leave these rolls up on these brackets for long periods of time.

A: I have had 86-inch rolls up for more than 8 months now, no sagging noticed.

Q: 7. Do these still come in sets of three? Also, what else do I need to buy to mount these to a wall. Thanks!

A: That which you see in the picture is a set for one roll of paper. If you want to operate 3 rolls of paper, you need 3 of those sets. The 2 white things in the picture fit inside the opposite ends of the cardboard tube and can be expanded to fit tightly inside it. Thus installed they become the axle and bearing for the paper roll and they must be supported by some type of wall mounted angle brace that you supply. Once you have a wall mounted support capable of holding the paper rolls, you will need to make an additional simple adapter to hold the axles in place on top of your support.

Q: 8. Can you use Sennheiser Headphone with boom mic's (Headset) with this machine? is it for one microphone set up only (i.e only one commentator)do you have Australian power plugs for these

A: Yes the THS4 with work with Sennheiser Headsets. It has one mic/headset input.We do not supply Australian power plugs, one can either use an adapter or find their own wall supply that has a 12 V AC 1 Amp output. See our website at a href= http://www.whirlwindusa.com target= _blank www.whirlwindusa.com/a to learn more and download the product manual.

Q: 9. Does this unit require external power? if so, how much and on what kind of connector?

A: The Whirlwind Line Balancer/Splitter requires no external power and is designed to split a single line level input signal into two balanced line level outputs. A choice of two output configurations is provided: one direct output and one isolated output, or two isolated outputs. The Line Balancer/ Splitter uses Whirlwinds TRSP-600L transformer and has a frequency response of 20 to 20kHz, 1dB @ +2OdBm.On the Line Balancer/Splitter are two male XLR jacks, one female XLR jack, a 14 jack and three switches as outlined below:INPUTEither of the two input connectors, a female XLR jack or a 14 TRS jack (Tip = Pin 2 and Ring = Pin 3) can be used for connection from a line level source, balanced or unbalanced. Use only one input at a time.OUTPUTSThe male XLR output connectors can be configured in one of two ways. The ISOLATED OUT/SPLIT 1 is always transformer isolated and the DIRECT OUT/SPLIT 2 is either directly connected to the input or transformer isolated, depending on the position of the OUTPUT SELECT switch.OUTPUT SELECTThis push-button switch selects the output mode of the unit. In the out position, the DIRECT OUT/SPLIT 2 provides a direct output signal and the ISOLATED OUT/SPLIT 1 provides a balanced 600 isolated signal. In the in position (the center of the switch changes to orange) both output connectors provide a balanced 150 ?isolated signal that is attenuated by 6dB from the input.GND/LIFTSEach of these switches disconnects the ground between the inputs and the XLR outputs when set to the LIFT position. Grounds remain connected when set to the GND position.This product is warranted to be free of defects in materials or workmanship to the original purchaser for a period of 3 years from the date of purchase.

Q: 10. So, just to be clear, this will hold 3 107 rolls of paper? Those rolls seem pretty heavy and this doesn't look strong enough to hold three.

A: Yes, as indicated under the Overview tab, the Impact Wall Mounting Kit for Holding Three Seamless Backdrops can support three (3) rolls of 9 feet x 12 yards (107 ) of seamless background paper. The Specifications tab for the Varidrive Set indicates it supports backgrounds up to a maximum of 22 lbs. For the record, a standard 107 x 12yds roll of seamless paper weighs approximately 17.5 lbs.