Finish your installation with a clean look with the stainless steel Whirlwind WP2/4MW 2-Gang Wall Plate. It features a two-gang design with four Whirlwind WC3M male XLR terminals to pass your wiring through the wall, reducing the appearance of cable clutter.

4x Whirlwind WC3M Male XLR Terminals    2-Gang Design

Related Questions and Answers

Q: 1. Does this unit require external power? if so, how much and on what kind of connector?

A: The Whirlwind Line Balancer/Splitter requires no external power and is designed to split a single line level input signal into two balanced line level outputs. A choice of two output configurations is provided: one direct output and one isolated output, or two isolated outputs. The Line Balancer/ Splitter uses Whirlwinds TRSP-600L transformer and has a frequency response of 20 to 20kHz, 1dB @ +2OdBm.On the Line Balancer/Splitter are two male XLR jacks, one female XLR jack, a 14 jack and three switches as outlined below:INPUTEither of the two input connectors, a female XLR jack or a 14 TRS jack (Tip = Pin 2 and Ring = Pin 3) can be used for connection from a line level source, balanced or unbalanced. Use only one input at a time.OUTPUTSThe male XLR output connectors can be configured in one of two ways. The ISOLATED OUT/SPLIT 1 is always transformer isolated and the DIRECT OUT/SPLIT 2 is either directly connected to the input or transformer isolated, depending on the position of the OUTPUT SELECT switch.OUTPUT SELECTThis push-button switch selects the output mode of the unit. In the out position, the DIRECT OUT/SPLIT 2 provides a direct output signal and the ISOLATED OUT/SPLIT 1 provides a balanced 600 isolated signal. In the in position (the center of the switch changes to orange) both output connectors provide a balanced 150 ?isolated signal that is attenuated by 6dB from the input.GND/LIFTSEach of these switches disconnects the ground between the inputs and the XLR outputs when set to the LIFT position. Grounds remain connected when set to the GND position.This product is warranted to be free of defects in materials or workmanship to the original purchaser for a period of 3 years from the date of purchase.

Q: 2. I have this system I use for 2- 9 ft paper rolls and it worked fine for awhile but now when I move the chains it isnt catching the rolls and unwinding as it should. I have tried taking it off and reinstalling and tightening and everything. any ideas on what could be the problem?

A: There is a tension control on the drive without the chain to control how loose or how tight the drive will move. If this does not correct the issue, I would recommend speaking with the manufacturer by calling 212-594-2120.

Q: 3. What is a "touch fastener"? Is it velcro?

A: While this is not the actual Velcro brand, it is a hook-and-loop material like Velcro. There are rectangular areas at each corner with the hook material that will stick anywhere on the rest of the Soft Wrap.

Q: 4. Do these still come in sets of three? Also, what else do I need to buy to mount these to a wall. Thanks!

A: That which you see in the picture is a set for one roll of paper. If you want to operate 3 rolls of paper, you need 3 of those sets. The 2 white things in the picture fit inside the opposite ends of the cardboard tube and can be expanded to fit tightly inside it. Thus installed they become the axle and bearing for the paper roll and they must be supported by some type of wall mounted angle brace that you supply. Once you have a wall mounted support capable of holding the paper rolls, you will need to make an additional simple adapter to hold the axles in place on top of your support.

Q: 5. Is this large enough to hold my new lumix zs70 camera?

A: Yes it will be.

Q: 6. Can I order just the metal chains?

A: You may order the chains as a replacement part through Impact directly. Here is a link to their contact page: http://bit.ly/29CMpL0

Q: 7. Can these be mounted on stands?

A: Hi , in light stands no , there is some mount that you can use for that , but for me is better in the wall

Q: 8. Once you get a 9' roll mounted, what is the total width including the mounts? I want to make sure I have enough clearance on either end.

A: The ends stick out 6-8 from the roll of paper. I would have at least an 11' wall to attach to.

Q: 9. so - assuming I get the aluminimum cores for 3 vinyl backgrounds 9x20s each; that'll easily put me over 40 pounds EACH -about 120 lbs. The max weight recommended for this is 22lbs (each) and I cannot find any solutions that accommodate a 40lb limit (each) even though that seems to be normal for vinyl. Are there ANY products that can accommodate Vinyl and be sturdy at the same time? (i.e. metal chains and not plastic etc)?

A: This background support is capable of supporting the weight of a vinyl background. https://bhpho.to/364HptE

Q: 10. ABout how high do you mount your bracket off of your wall? I will have the 9' wide rolls. Do you hang them 10-12' high?

A: There is no set high to mount it. You can mount it at the height needed.