The black SKB iSeries 2421-7 Waterproof Case with Cubed Foam Blackfrom SKB iSeries 2421-7 Waterproof Case with Cubed Foam Blackis made from an injection-molded, high-strength, polypropylene copolymer resin that is not only impact resistant, but also UV, solvent, corrosion, and fungus resistant. The molded-in hinge provides additional strength and features a gasket for watertight security to approximately 3'. This case is typically used to store and transport delicate equipment such as cameras, electronics, mics and mixers, cables, or musical equipment. This case has cubed foam for easy customization.

Access to the interior is via four trigger releases with locking loops that will accept user-supplied locks. An equalization relief valve protects your gear especially against changes in pressure such as when you're on an airplane. For portability, there's a snap-down rubber molded cushioned handle.

Holds Electronics, Cameras, Mics    Gasketed, Waterproof, Airtight    Automatic Pressure Equalization Value    Injection-Molded Polypropylene Resin    UV and Solvent Resistant    Corrosion and Fungus Resistant    Trigger-Release Latch System    Accepts User-Supplied Lock    Molded-In Hinge    Snap-Down Rubber Cushioned Grip Handle

Ultra-high-strength polypropylene copolymer resin

UV, solvent, corrosion and fungus resistant

Complete gasket seal makes these cases absolutely watertight

Automatic ambient pressure equalization value

Resistant to corrosion and impact damage

Continuous molded-in hinge

Patent pending trigger-release latch system

Rubber over molded cushion grip handle

Locking loops to accept a customer-supplied lock

Related Questions and Answers

Q: 1. Can this case hold D610 with battery drive attached without it pressing hard on the egg crate foam?

A: The D610 is 4.4 tall and the MB-D14 grip adds about 2 so around 6.4 tall. The manufacturer states the case can accommodate 7.5 tall gear. You should be good to go.

Q: 2. Will this fit a Canon C100 Mk I?

A: I not sure ...

Q: 3. Will this work for the C100 Mk II?

A: It worked well with my C100 mkI so I'd say you'll be fine!

Q: 4. Is the SKB 1510-6 (with lid organizer) deep enough to close easily on a Nikon D7100 with battery grip and an Arca quick-release plate attached? Thanks!

A: Yes, according to the depth of the case and the combined dimensions of the camera and grip, it will fit.

Q: 5. What's the depth from foam base to the foam top? What is the interior width & length with the ThinkTank outer padding?

A: The SKB iSeries 1510-6 Case with Think Tank Photo Dividers & Lid Foam has a 1.75" / 4.45 cm (Lid Depth) and 4.25" / 10.79 cm (Base Depth).

Q: 6. No dimensions listed. The only dimensions are for the box BH ships it in. What are the internal dimensions of this case?

A: The interior dimensions are L x W x D: 17 x 11.5 x 6.16" (43.18 x 29.21 x 15.65cm) with the foam removed.

Q: 7. Would this case hold a G50, being that the G50 is basically a XA40 without the handle?

A: The Canon G50 will fit in this case, however, it will not be as effective at protecting the camera. The excess space (for the top handle) gives the camera room to move around inside the case. If you plan to use this for keeping your camcorder organized then this case will work very well. All of the accessories are the same for both camcorders (except audio).

Q: 8. the SKB Iseries 1711-6, has its lid organizer?

A: It may be discontinued by SKB you can go to the SKB website and lookup the SKB iseries 1711-6 and see if they sell that model with a lid organizer maybe B&H does not stock it. I can say that I bought the SKB iseries 2011-8 with lid organizer from B&H and love it! I think that the 1711-6 for me would be just a little to small. Also you get that the model number is actually the dimensions? So for example 17 x11 x6 go with the 2011-8 you will be happier!

Q: 9. Will this case hold a Canon 70-200 2.8 IS II lens standing up (vertical), or does it have to lay down (horizontal)?

A: The lens is about 8" long and the dimensions of the case are 20.4 x 11.4 x 7.5", so the lens will fit in two of the dimensions, but not in the third, shortest, dimension.

Q: 10. Is the 1510-6 also a rolling case ?

A: Hi Steven, The 3i-1510-6 case does not have wheels. The smallest case we offer with wheels is our 3i-2011-7DL. For that same sized case we have some other interior options. 3i-2011-7DT, 3i-2011-7DZ, and 3i-2011-7BP.Thank you,Will