Mount your 39 to 80" display weighing up to 125 lb with the black Kanto PDX680 Full-Motion Wall Mount. It supports displays with 200 x 100 to 700 x 400mm mounting patterns and can extend from the wall up to 24", or fully retract to provide a 2" profile. It provides -3 to 15° of tilt, up to 170° of swivel, and has adjustable horizontal leveling.

Supports 39 to 80" Displays up to 125 lb    200 x 100 to 700 x 400mm Mount Pattern    -3 to 15° of Tilt Adjustment    Up to 170° of Swivel Adjustment    Adjustable Horizontal Leveling

The design of the PDX680 allows your display to sit as close as 2" from the wall when fully retracted.

The H-frame mounting bracket accommodates VESA sizes from 200 x 100 to 700 x 400mm. The mounting arms allow you to raise or lower your display depending on its VESA pattern.

Magnetic covers go over the lag bolts to help give the wall plate an elegant look. Remove the covers when you install or remove the wall plate from the wall.

Despite its low-profile design, the PDX680 can extend up to 24" from the wall, allowing you to tilt and swivel your display or extend it from an alcove.

The solid steel frame of the PDX680 can hold up to 125 lb, even at full extension.

The articulating arms of the PDX680 allow for up to 170° of swivel with a 39" display; the larger the display, the less swivel the mount will be able to provide.

The tilt mechanism lets you angle your display up to 15° forward or 3° backward. Once you reach your preferred viewing angle, tighten the nuts to secure your display in place.

Four cable management raceways are attached to the bottom of the wishbone arms. These are accessed by loosening a screw, twisting them to the side, laying the cable, and re-inserting the screw. Route multiple cables down one side, or power and HDMI down opposite sides, whichever you prefer.

Related Questions and Answers

Q: 1. Can the OctaBox be used with the Paul C. Buff 8-slot ring I already have?

A: Rotalux softboxes require a Rotalux ring that is non standard sized.

Q: 2. Do you carry the V-Motion motor kit for this product?

A: The Rat Rig 39" Single Rail V-Slider (B&H# RAV100) can be used with three motor products that we carry. First, there is the Rat Rig V-Motion Standard Motor (B&H# RARRVMM2GP, https://bhpho.to/3L2qezP). For speedier movement, there's the Rat Rig V-Motion Fast Motor (B&H# RARRVMM3GP, https://bhpho.to/3MJl7FH). If you are shooting a time lapse, use the Rat Rig V-Motion Time-Lapse Motor (B&H# RARRVMM1GP, https://bhpho.to/43AlVmA).

Q: 3. Can this modifier be used with a Profoto b10?

A: Yes you can use this softbox can work on a Profoto B10 by using the Elinchrom Rotalux Speed Ring for Profoto B1 and B2 OCF Flash Heads, B H # EL26547 https://bhpho.to/3it4U8A

Q: 4. Is there something like this for my Alta Pro 263AT (SBH100 head) that has a thumbscrew? It's a huge pain having to use a coin or tool to attach this.

A: Johnny 5I am 99% sure this will work in that plate. I should take my own advice and do the same.I meant to buy this when I bought the tripod and forgot !!Pretty sure that will work for you though.What a pain it is using the screws.Good LuckCheck out what I found on B&H Photo Video https://a href= http://www.bhphotovideo.com/c/product/1068642-REG target= _blank www.bhphotovideo.com/c/product/1068642-REG/a

Q: 5. What stop is the diffusion panel?

A: The Photoflex LitePanel Translucent Fabric Diffusion (39 x 39 ) included with the Photoflex LiteReach Plus with 39 x 39 LitePanel Kit offers one (1) stop of diffusion per layer.

Q: 6. Will the Vanguard QS 39 fit well on the Vanguard Tracker 2 tripod? Thanks

A: Yes the QS-39 plate is compatible with the Vanguard Tracker 2 Tripod.

Q: 7. Is QS-39 plate compatible with the Sirui L-205 head?

A: No, but most any Arca Swiss plate ought to work with the L-205. Here is the recommended plate for the Sirui. Sirui TY70-2 Arca-Type Pro Quick Release Plate B&H # SISUTY702

Q: 8. Will average sized speedrings fit the rods of this box, or does it need a proprietary ring?

A: You will have to get a proprietary speedring that's made by Elinchrom for different type light mount

Q: 9. I’m looking to make the Rotalux into and indirect source, like my deep Octabox. I’ve heard there is an adapter, anyone know what it is called? Thanks.

A: Not aware of any such product made by Elinchrom, Perhaps they meant the Deflector plates which is listed in the accessories on this item.

Q: 10. What speedring do I need to purchase to use this with a Profoto B1?

A: You need this speedring. https://bhpho.to/33uuGQm