Mount your projector to the ceiling with the black Kanto P101 Ceiling Projector Mount Blackand save floor space or give your presentation/home theater room a cleaner look. With 20° of up/down adjustment and 360° of swivel, this mount can be adjusted to match the location of your screen, even if your ceiling is slightly tilted. Included extension tubes can be used to lower the projector from just 3" to anywhere from 9 to 12" below the ceiling. Included hardware can secure most standard projectors to the mount; however, hardware for securing the mount itself to your ceiling is not included, and must be purchased separately. This version of the mount is powder coat finished in black and is constructed of sturdy aluminum.

Compatible with Most Projectors    Drops 3" or 9-12" Below the Ceiling    Can Be Used on Flat or Angled Ceilings    20° Tilt Range    360° of Swivel    Aluminum Construction    Black Powder Coat Finish

Related Questions and Answers

Q: 1. anyone know the approximate recording times (4k) with this battery 99wh with canon r5c?

A: When using the SmallRig VB99 Mini V-Mount Battery with the Canon R5C, you can expect 5.5 - 7hrs run time when recording 4k content.

Q: 2. hi, does this fit the new forza 150. they are the same mount. or does it go to the forza 200/300/5-- projection spot?

A: Yes this projection attachment mounts and works with the Forza 150

Q: 3. Which cable/adaptor, DC out to dummy battery, would work with this battery and a Sony a7IV?

A: The SmallRig VB99 Mini V-Mount Battery (99Wh) can power a Sony a7 IV by using the Kondor Blue D-Tap To Sony a7S III Dummy Battery NP-FZ100 Cable.

Q: 4. does this come with both size gobo frames? I know the older model didnt have the M size.

A: The Nanlite Projector Mount for Forza 60 and 60B LED Monolights (36°) comes with one gobo holder and that is for size B.

Q: 5. Would this battery work with sony fx30 which needs 9v/3a through dtap with Kondor blue Dummie NP-fz100 to D-tap? Thanks

A: When using a regulated DTAP dummy battery cable with the Smallrig VB50, and the Sony FX30 camera, it will provide the proper power to your camera. Kondor Blue D-Tap To Sony a7S III Dummy Battery NP-FZ100 Cable BH #KODTSA7SDB

Q: 6. Are all of the screws and sockets on all parts 1/4-20?

A: Yes they are

Q: 7. Does this have an on/off switch?

A: The Tilta PD V-Mount Battery Plate (Black) does not have an on/off switch.

Q: 8. Did they fix gobo holder size to real B..?

A: ************DUPLICATE DUPLICATE DELETE ****************************

Q: 9. can extensions be added to this arm for example if we need to to be 18 inches instead of 9 ? I am looking for a wall mount that can be swung out of the way for a small camera so when we use the camera we will swing it out when we are not using the camera it can be stored against the wall

A: Yes, I have ordered many of these units and mixed and matched the poles to make several mounts of varying sizes. Each pole extension uses the same 1/4 -20 screw size, so even the camera could mount directly to the pole rather than the ball mount.

Q: 10. Can i use the 8V DC output to power my FX30 with a dummy battery that has a 7.4V DC input?

A: It is recommended to only connect dummy batteries that take an 8V input to the 8V DC output of the SmallRig VB99 Mini V-Mount Battery (99Wh, Black) so as to prevent overvoltage from damaging your dummy battery or camera.