The short CineMilled Pan Arm Extension for DJI Ronin Gen 2 Shortfrom CineMilled Pan Arm Extension for DJI Ronin Gen 2 Shortis a single extension which diagonally displaces your DJI Ronin pan arm by 1.8", enabling you to properly balance an extended camera setup. It also provides full tilt down and up clearance on long camera builds. With this pan arm extension, you will be able to use your DJI Ronin with a Sony F55, F5, or FS700 or with a Red Epic/Dragon with long zoom, a matte box / filter, or a regular back battery mount while your camera stays properly balanced.

Diagonally displaces your DJI Ronin pan arm to properly balance an extended camera setup

Related Questions and Answers

Q: 1. Has anyone used this gimbal with a Nikon Z6 with the Nikkor 24-70 f/2.8 S lens? If so, how did it handle the weight?

A: This gimbal has an 8 pound load capacity. It should be able to handle that combination of camera and lens very well.

Q: 2. Will it work with the thumb controller?

A: Currently no DJI thumb controller, wireless or otherwise, is compatible with the Ronin-S. The Ronin-S comes with a canbus-sbus cable that will allow you to use third party controllers and reeivers that use sbus.

Q: 3. Would this be able to support and work well with Panasonic HC-X1?

A: The Ronin-S does have a load capacity of up to 8 pounds. However it is designed to work with Mirrorless and DSLR cameras, not a mid sized camcorder. You may be able to balance the HC-X1 on it, but it is not something we recommend.

Q: 4. Is Ronin-S compatible with Eva1?

A: The Ronin-S is designed to hold a DSLR or Mirrorless Camera camera, not a digital cinema camcorder like the EVA-1. The Ronin M would be more appropriate for the EVA-1 as a stabilizer. DJI Ronin 2 3-Axis Handheld / Aerial Stabilizer Basic Combo B&H # DJRON2BASCOM.

Q: 5. does the plate of the S fit the SC?

A: Unfortunately no, the Ronin SC plate is not as wide as the Ronin S plate.

Q: 6. Does the Ronin-S provide camera control for the Canon 1DX MKiii?

A: As of writing (9/21/2020), the 1DX Mk III is not on DJI's list of cameras compatible with the Ronin-S. Please see DJI's support page here (https://bit.ly/2FNb82d) for more information. This list is subject to change, and hopefully the camera is made compatible in the future!

Q: 7. Does the DJI Ronin-S support canon G30, G40, XA35, or similar cameras?

A: We have not tested those specific cameras, but there shouldn't be any specific balancing and mounting issues. Some longer cameras, especially those with eyecups, can hit the roll motor when tilting up.

Q: 8. Hello, is this fully compatible with a Sony a7s?

A: The Sony A7S will work very well with the Ronin-S. The kit does not include any cables though, you would need to purchase separately B&H # DJRONINP13CB if you wanted to control start/stop recording from the gimbal. https://bhpho.to/2DZF5sE

Q: 9. Is C100 Mark II compatible?

A: This gimbal is designed to work with Mirrorless and DSLR cameras. However you still may be able to balance a camera like the C100 Mark II on it. More than likely you will need to remove the top handle from the C100 Mark II and you may not have the full range of motion with the gimbal when using it. However because of this gimbals 8 pound load capacity it is still possible to balance it.

Q: 10. Has anyone experienced any problems with the lock mechanism of the quick release plate? I received mine, the plate locks but it does not unlock when the lever is pulled back to its unlocked position.

A: Hey M C, are you making sure to press the silver button on the side of the mount?