The highly flexible QSC SPA2-200 2-Channel Power Amplifier is an advanced Class-D amplifier with Energy Star rated efficiency well suited for smaller installations including meeting rooms or BGM zones. The convection cooled amplifier is designed to conserve energy. An auto-ramp circuit ensures quiet and fast power up from standby when a signal is present and seamless power-down following 25 minutes of inactivity, dramatically reducing power consumption.

The rear panel utilizes Euroblock connectors for inputs and outputs as well as remote inputs. Each channel of the SPA2 provides 200W of power, while the bridge mode provides 400W into 4 or 8 ohms and 350W into 70/100V.

Energy Star Qualified    Class-D Topology    4 and 8 Ohms + 70/100V Operation    Bridgeable Outputs for Higher Power    Auto-Ramp Provides Quiet Power Up/Down    Euroblock Input, Remote Input, Output    Rack-Mountable 1 RU, 1/2 Rack Width    Includes Rack Ears + Mounting Brackets    Connector Pack and Power Cord Included

• Provides up to 200W per channel into Low-Z loads at 4 and 8 Ohms
• Energy Star qualified SPA Series employ an efficient class-D design to conserve energy and reduce operational cost
• Delivers up to 350W into 70/100V when bridged
• Rack-mountable 1 RU, half-rack width enclosure—the SPA Series can be mounted in 1 RU, 1/2 rack space, and their clever joining brackets enable easy under table and wall mounting

Related Questions and Answers

Q: 1. Can the 4-pin DC output power an Arri L5-C (with two bricks attached)?

A: The DC output is a pass though for the AC. It can only charge the batteries, batteries cannot be used for power.

Q: 2. What is exactly included with this item? I have a feeling there may be more or less than listed.

A: This is only the LED mat without a power supply, dimmer or mounting hardware.

Q: 3. PTAU45 POWER STEREO AMP: What is the frequency response of this amp?

A: Frequency response is rated at 20Hz-20KHz. We connect all sorts of electronics to these and find there sound quality to be just fine for small to medium group listening. Your speakers will likely be the limiting factor if you choose to run these amps for these groups.

Q: 4. Can this charger be used to charge fxlion nano series?

A: Yes

Q: 5. What is the speaker Output ohms for a pyle pro ptau45 mini 120 watt?

A: This amp has a 4 ohm speaker output.

Q: 6. Which V-mount batteries does this charger not work with?

A: In general V-Mount battery systems are interchangeable. This should work with any V-Mount battery.

Q: 7. Can you charge the idx 198 batteries with this charger?

A: Yes

Q: 8. Can I connect my nextbook for better sound?

A: You can hook up any audio source with an auxillary cord. I've used phones, iPads, and IPods without an issue so I'm assuming your Nextbook would be similar.

Q: 9. I have an existing set of speakers going to my pool deck (Ch.2), and a set at the pool house (Ch.1). I'm looking to amplify the ones on the deck (Ch.2) so I have a balanced volume. Can I connect the existing speaker output (Ch.2) speaker to the input AUX. of this amplifier then run the speaker output from the amp to the pool deck and boost the volume?

A: Adjust the balance control.

Q: 10. Can this charger be used to charge Switronix batteries, like the Hypercore Slim?

A: In order to obtain the best performance and maintain your warranties, you should always use the same manufacturer for the batteries and chargers. That being said, if you have the battery/chargers that match in terms of chemistry and intelligence, probably the battery will charge. However, be aware of any burn damage on pins and the fact you may be reducing the life of your batteries.