The Radial Engineering Catapult TX4L is a four-channel snake that is designed to route four channels of line-level signal across long distances using shielded Cat5/Cat6 cable, doing so with little to no signal degradation. As such, it’s useful in live-sound reinforcement applications, as it allows live sound stage techs to use relatively affordable cable to secure quality audio connections around large stages and venues. It’s also suitable for system contractors who can now utilize pre-wired networks to move audio throughout disparate rooms.

The Catapult TX4L gives you four XLR input jacks, as well as four XLR transformer-balanced through-outputs optimized for line-level signal. You’ll also note the two RJ45-type etherCON connections. One is an output, for use with the RX4L on the receiving end. The other is a throughput, and can be implementing in routing signal to additional Catapults. In total, you'll have the ability to split and route line-level signal to three different locations.

A ground-lift switch helps eliminate any noise issues on the Cat5 or Cat6 line, while a steel handle provides easy transport, and four bumpers protect the Ethernet jacks and ground-lift switch from wear and tear.

For Routing Line-Level Audio via Cat5/6    For Use with Catapult RX4L    4 x XLR Inputs    4 x Line-Level Isolated Outputs    1 x RJ45 Output, 1 x RJ45 Through-Output    For Live-Sound Applications    For Networking Audio Throughout Rooms    Ground-Lift Switch on Cat5 Connection    Steel Handle & Rubber Bumpers    Military-Spec Grade Circuit Board

• Glass-filled, nylon XLR connectors 
• Nickel-silver contacts 
• 4 x XLR through-outputs with line-level transformer isolation for additional routing
• 1 x Ethernet through-output for feeding additional Catapult models
• Protective steel handle facilitates convenient transportation
• Durable powder coat
• Ground lift for the Cat5/Cat6 cable’s ground path to mitigate ground-loop noise
• 4 x bumpers used to protect Ethernet connectors and ground-lift switch from damage
• Double-sided, military-spec grade circuit board for durability, full ground plane, and a marked reduction in radio-frequency interference
• Radial push switches with durable metal outer casing, rated at over 20,000 cycles

Related Questions and Answers

Q: 1. Does the back have a Standard Anton Bauer 3 Stud Mount?

A: Yes, this can be attached to a 3-stud Gold Mount Anton Bauer plate.

Q: 2. So Bought this through B&H. I notice it does not come with an AC power Outlet... Is that the case? If so, Where do we buy it from I guess.

A: That is correct. You would have to buy the Henry Engineering Henry Engineering Multi-System Power Pod. This is the B&H part number for the Power Pod BH #HEPP.

Q: 3. I have an old impact T-616 receiver. Will it work with this new model transmitter?

A: No. This is not backward compatible.

Q: 4. Could this unit be used to split clearcom or rts units?

A: This unit is meant to split audio only, and is wired differently than communication systems. We do carry a splitter for RTS, which is the Telex TW-5W 1 In, 5 Out Splitter Box, B&H # TETW5W.

Q: 5. Can I use this PowerTrigger on a Nikon D7200 and Westcott Strobelite Plus?

A: Not familiar with Nikon. I shoot Cannon

Q: 6. Regarding the question above. I was told by Radio Popper that I could connect this by wire for triggering while I have a flash in the hotshoe. Here is the response... Yes, you can indeed connect the Jr2 transmitter via the camera PC sync port, freeing up the hot shoe for an on-camera flash. All you need is a 3.5mm to PC sync cord. Can you confirm this?Thanks,Brian

A: Yes the JR2 transmitter has a 3.5 port so from a cameras pc sync port you can attach this to the camera and not use the hotshoe.This is one cord of many that will work,Paramount PW-PC1 Sync Cord - Miniphone to Male PC - Straight - 12 B&H # PAPM1 Mfr # 17PWPC1http://bhpho.to/VA0PkD

Q: 7. Can this Jr2 transmitter trigger Jrx receiver?

A: I think it can, but the folks at Radio Popper are super helpful I would call them to verify!

Q: 8. Can this unit accept a direct microphone feed from a press conference without a mult box? And is it powered by batteries?

A: The Radial Engineering Exo-Pod Broadcast Splitter with XLR & 3.5mm Connections is designed to accept a balanced line-level signal from a mixer or similar device. It does not require power.

Q: 9. I have a set of Photogenic strobes (from the early '90's). Will this work with Photogenic strobe models from that time frame?

A: If your Photogenic strobes use the standard IEC power cable and has either a 1/8 (3.5mm) miniphone sync terminal or 1/4 headphone sync terminal, then yes, the Impact PowerTrigger 16 Channel AC Transmitter and Receiver Set would be compatible for use with your strobe units.

Q: 10. Will this trigger more than one flash unit or do two receivers need to be purchased?

A: A receiver for each flash/strobe needs to be purchased.