With a maximum height of over five feet and a minimum height of just over two feet, this set of E-Image 2 Stage Aluminum Tripod Legs 75mm Bowlfrom E-Image 2 Stage Aluminum Tripod Legs 75mm Bowlprovides a stable platform for your 75mm fluid head and features a two-stage / three-section design. The aluminum legs incorporate E-Image's Mono-Lock design that allows you to adjust the leg height using the one locking lever at the top of the each legs.

The legs support up to 88 pounds of head, camera, and accessories, while extending to over five feet in height, with a minimum height of just over two feet. The aluminum alloy construction provides you with a balance of strength and durability and is a lower cost option to carbon fiber legs. The legs feature a removable, adjustable, mid-level spreader that allows you to set up the legs on uneven surfaces. The legs also incorporate spiked feet for increased grip on soft surfaces, and the included spike covers allow you to use the legs on hard/slippery surfaces. An integrated leg wrap/safety extends from the bottom of one leg and wraps around the legs when closed, keeping the legs together during transport or storage.

75mm Bowl Fitting    2-Stage Leg Design with Mono-Lock    88 lb Payload    62" Maximum Height    24.75" Minimum Height    Aluminum Alloy Construction    Mid-Level Spreader    Removable Anti-Slip Pads / Spike Covers    Integrated Leg Wrap/Safety

Mono-Lock design allows you to lock and unlock the three sections of each leg using only one locking lever. The rotating lever provides a robust clamp mechanism that secures the legs and prevents them from slipping once locked. The single lever on each leg allows you to quickly lock the leg height without having to use two levers, making for a quicker workflow and sparing you from having to bend down to open a bottom leg lock to raise the legs.

The legs feature spiked feet that provide solid purchase in soft surfaces, the included mid-level spreader allows you to use the legs on uneven surfaces, and the rubber feet allow you to shoot on hard/delicate surfaces.

Related Questions and Answers

Q: 1. Does this tripod come with a bag?

A: It doesn't but its worth the price.

Q: 2. can you remove the head and put on a short glide?

A: The short answer is yes.You will need an adapter. I suggest either one of the attached adapters seen below.The Manfrotto has a low profile and is very solid. However, there is no leveling possible, for it holds the head in just one position. The ikan adapter is more expensive, rests the head and camera about 2 higher. However you can level with it.

Q: 3. Does the head have drag control steps?

A: This GH08 FLUID HEAD (E-IMAGE) head has fixed drag control for pan and tilt.

Q: 4. Can I ship immediately if I place an order?

A: As of the time of this posting, December 3rd 2018, this product is in stock and ready to ship.

Q: 5. Does the new Manfrotto 2 in 1 spreader fit with these legs? Ikan does not have a telescopic spreader and the ground spreader is too much of a hassle.

A: It does not. The Manfrotto 2 in 1 Tripod Spreader, BH #MAMVASPR2N1, is only compatible with the Manfrotto 645 FTT and 635 FST series tripods.

Q: 6. Hi! I plan to use this tripod with a Sachtler aktiv fluid head, but for that I need to make sure of the compatibility. There is a centered hole in the bowl where the head is mounted and I would like to know it's diameter. Could you please check it for me?

A: Yes. The following unit will adapt to the 75mm bowl drop.

Q: 7. Are there other feet that will fit this tripod? The ones that come with it are not good and fall off easily.

A: We are not aware of alternative feet that you could use with this tripod. The only feet we know that will work are the included ones.

Q: 8. Hi, can I take the tripod head off and mount a varizoom solo jib in it? Would it hold?

A: This tripod has a load capacity of 17.6 pounds, while a Varizoom Solo Jib that is Carbon Fiber will weigh right around 7 pounds. If you keep the weight of the camera you are putting on it low this tripod will be able to handle the Varizoom Jib. The jib will also connect right to the tripod head, you would not need to remove it.

Q: 9. Will a manfrotto 501 plate be compatible?

A: We're afraid not. This system is compatible with the E-Image EH6P Quick Release Plate, BH #EIEH6P.

Q: 10. Will the Manfrotto 504HD head fit on this tripod? https://a href= http://www.bhphotovideo.com/c/product/683559-REG/Manfrotto_504HD_504HD_Fluid_Video_Head.html target= _blank www.bhphotovideo.com/c/product/683559-REG/Manfrotto_504HD_504HD_Fluid_Video_Head.html/aDo I need any adapters?

A: It should fit, I used it with Manfrotto 502 and 516 fluid head. This is one of the best designed tripods I've ever used. One lever controls both leg extensions at the same time. Very quick setup.