The Ambient VSLOT V-Mount Chassis for Wireless Receiversby Ambient VSLOT V-Mount Chassis for Wireless Receiversis for cameras with a 25-pin D-sub, Unislot connector. It can be used to mount two wireless receivers between the camera and battery supply, allowing the power to be looped through to the camera, powering the audio receivers. It features a TA5M jack attached at the bottom, offering two balanced outputs for dual receivers. Dangling cables could become a relic of a day gone by, like bulky oversized power adapters and shoebox-sized cellular phones, thanks to the manufacturing of cables that are customized for almost every camera type. Thanks to the Ambient VSLOT every V-Mount equipped camera can be transformed into a compact ENG camera system. The VSLOT includes a standard VSL-2X3 adapter cable.

For 25-Pin D-Sub Unislot Connector    Mounts Receiver Between Camera, Battery    Powers Wireless Receivers    TA5M to Two Balanced Outputs Cables    Adapter Cable is Included

Related Questions and Answers

Q: 1. Can I connect to PC and making live streaming through it?

A: If you want to live stream with this you would still need a video capture card from the receiver to your PC.

Q: 2. Can I connect an iPhone and see the image using WiFi?

A: Yes. But the following will be needed. Please review the following item Apple Lightning Digital AV Adapter BH #APMD826AMA • MFR #MD826AM/A https://bhpho.to/3sOG3Rj

Q: 3. Does the TC-out and Sync-out require two different cables or are they the same?

A: A single cable on the output carries timecode and genlock/wordclock.

Q: 4. I am looking for a good solution to mount this to a camera. Is there a 1/4-20 mount (or similar) for this?

A: There is no mount made specifically for the Ambient Recording ACN-CL. Often times people use velcro patches or ties to fasten the unit to a rig. Alternatively, you can look at some of the 1/4-20 clamps we have. I recommend using a patch of velcro though.

Q: 5. This can generate timecode, but can it generate genlock. Also, can it do both concurrently?

A: Yes, the Ambient Recording ACN-CL Lockit Compact Wireless Timecode Synchronizer can output both Genlock and Timecode at the same time.

Q: 6. Can I set the Lockit to mirror my audio recorder's timecode then connect it to my camera, or do I need two devices to accurately sync timecode for both audio recorder and camera?

A: Yes it can however it depends on the audio recorder. Typically the Lockit generates the timecode and you sync the audio recorder + Camera to the Lockit's timecode. Ideally you would use 2 Lockits to sync everything however, It is possible to use just 1 Lockit if you like. You can use the Lockit to generate timecode then sync your audio recorder disconnect the audio recorder and then use the same Lockit to sync your camera. In a scenario like this we recommend re-synching the devices every few hours to make sure that your camera and audio recorder are still in sync.

Q: 7. Will this device accept an SDI signal as a genlock input, broadcast this over ACN, and output a wordclock referenced to it? I see lots of discussion of genlock output, but not input. I have a camera without genlock, and I want to avoid pops when combining HDMI + AES - SDI. Therefore I want to synchronize the audio ADC to the un-genlockable camera.

A: no this device will not work as a genlock for a camera without genlock, it's base/fundamental mode of synchronization is time code

Q: 8. Does this include 2 units - one for the audio recorder and one for the camera, or do I need to buy 2?

A: This is for a single unit. It does not include two units.

Q: 9. Does this work for SLX4 also?

A: Yes

Q: 10. Can it do pass-through charging? (i.e., is this fully functional while also plugged in to charge at the same time?)

A: No, the Ambient Recording ACN-CL Lockit Compact Wireless Timecode Synchronizer when plugged in will receive power but will not actively charge also. To charge, it will need to be powered in the off state.