The white JBL PD6200/66 Passive Biamp Loudspeaker Whiteis a versatile, high-output speaker well suited for professional installations such as performing arts facilities, theatrical sound design, auditoriums, houses of worship, live music venues, night clubs, sports facilities, and theme parks.

The PD6200/66 is comprised of the JBL CMCD-82H cone midrange compression driver with integral 8" diameter Differential Drive dual voice coil driver, and a 2432H, 1.5" exit high-frequency compression driver. The large format PT Progressive Transition waveguide provides a 60 x 60 coverage pattern. The waveguides are rotatable so the loudspeaker system can be used in either the vertical or horizontal orientation. High-slope passive networks minimize band overlap. Well-controlled off-axis response enhances arrayability. The PD6200/66 will perform as either a bi-amped or passive cabinet, at the flick of a switch.

High Output    8" CMCD Cone Midrange Compression Driver    1.5" Exit HF Compression Driver    Progressive Transition Waveguide    Rotatable Horns for V/H Deployment    60 x 60° Coverage    Frequency Response: 200 Hz to 18 kHz    NL4 speakON and Barrier Strip Inputs    DuraFlex Finish    M10 Threaded Attachments for Rigging

•  High-power 8" dual-coil CMCD cone midrange compression driver provides high sensitivity and high-continuous SPL capability along with low distortion, extended bandwidth, and improved phase coherence
• Large-format neodymium HF driver provides clear, intelligible high-frequency projection
• Large PT Progressive Transition waveguides provide consistent 60 x 60° pattern control, low distortion at high SPL levels and smooth frequency response
• Rotatable mid- and high-frequency waveguides allow either horizontal or vertical cabinet orientation
• Sophisticated, steep-slope passive crossover network with switchable bi-amp/passive crossover modes

Related Questions and Answers

Q: 1. Is the price for each or a pair?

A: The price is for a single unit, not a pair.

Q: 2. What bracket do we use with the ac 28w speaker?

A: JBL recommends the JBL U Bracket f/Models AC28/XX white finish7. That would be B&H part number B&H # JBMTU28WH.

Q: 3. Is it okay to Bi-Amp JBL C211?

A: The JBL Two-Way ScreenArray Cinema Loudspeaker BH #JBC211 may be bi-amped: For Single-wire passive operation, leave the jumpers in place (jumpers link the LF+ and HF+ terminals together and the LF- and HF- terminals together). For Bi-wire passive operation, remove the jumpers and wire the LF± and HF± terminals to the respective amplifiers Designed for small cinemas and VIP rooms for a maximum throw of 52'

Q: 4. Idol pro IP -300 has 2 channels 500w+500w 4ohm,350w+350w8ohmpoweroutput(RMS) and 3500w+3500w power(peak) is fit jbl prx412m

A: A pair of the JBL PRX412M Two-Way 12" Passive Speakers can be used with the IDOlpro IP-300 Digital Amplifier. The amp has banana connectors and the speakers have combo jacks that accept Speakon NL-2 or 1/4" connectors.

Q: 5. I'm not familiar pass through. If I have an amp sending 600w out the channel, and then two speakers are connected, will the power be halved? Or will each speaker see 600w?

A: If your amplifier is a stereo amp (two channels), at 600 watts per channel at 8 ohms, then it will be appropriate for two of these speakers. A single-channel amplifier would have to put out 1200 watts at 4 ohms in order to power two of these speakers. Please call our Pro Audio Department at 800.606.6969 to better assist you.

Q: 6. What is the length of the C211 speaker

A: Dimensions 31" H x 40" W x 12" D (79 x 102 x 30.5 cm)

Q: 7. Does this speaker support upper and lower pole mount options?

A: The Mackie C200 Passive 10" 2-Way Loudspeaker has a single pole mount socket on the bottom of the speaker and also has an asymmetrical trapezoidal cabinet for floor monitor positioning.

Q: 8. What kind of power amplifier do I need to power this passive speaker?

A: The Crown Audio XLi 800 Stereo Power Amplifier, B&H # CRXLI800, set to bridged mono mode, would be a good choice for powering one JBL PRX415M passive speaker, which requires 600 watts of program power.

Q: 9. do these connect with a speaker wire or something else?

A: The JBL SCS 12 Two-Way Spatially Cued Cinema Ceiling Passive Surround Loudspeaker BH #JBSCS12 will require connection to an amplifier via speaker wire/cabling.

Q: 10. I am looking to have these speakers controlled by a lecture amp ?

A: The JBL SCS 12 Two-Way Spatially Cued Cinema Ceiling Passive Surround Loudspeaker BH #JBSCS12 should have a minimum of 100 watts input at 8 ohms. Check your lectern's amplifier output rating.