The PANAVISE ActionGrip Suction Cup Mount Kitincludes multiple components that let you build three different suction cup configurations for your action camera. "Shorty" mode provides a low-profile setup, letting you get the camera close to the mounting surface. "Single Knuckle" mode adds more height and provides articulation so you can adjust the camera angle. And "Double Knuckle" mode sets the ActionGrip at full height and provides maximum adjustability, allowing for more camera angles.

The major components are made of aluminum. The suction cup itself is made of a premium material that keeps its hold in hot and cold weather. Among all the included components are a mounting platform with a 1/4"-20 screw and a 3-prong adapter for attaching an action camera.

Create 3 Different Suction Cup Setups    Shorty Mode Low-Profile Configuration    Single Knuckle Mode with Articulation    Double Knuckle Mode with Max Adjustment    Suction Cup Built for Hot/Cold Weather    Includes 1/4"-20 Platform & GoPro Mount

Related Questions and Answers

Q: 1. When using with a gimbal like the RS2 does t hevibration damping match up to a Cloud Mount or Kessler Killshock? It says "minimized vibration" but I can't tell where that is happening on this rig.

A: The center mount for the Video Sucker Suction Cup mount is connected to the legs by a double ended ball joint that helps isolate the mount from external vibrations. For something that is comparable to the mounts noted, I would recommend CAME-TV's GS10 Video Camera Stabilizer Arm (BH #CAGS10).

Q: 2. If I have it in the outside of a car going 70 mph is it strong enough?

A: Yes it is: Mount Proven at Speeds of 150+ mph Maximum holding strength requires attachment to a clean surface

Q: 3. How easily are you able to remove the mount after use/change its location on the vehicle?

A: I have the GoPro suction mount. It is very simple to attach, remove, relocate. Position the mount and camera where you want it. Press the center of the mount firmly into the windshield, then flip down the lock lever, done! To remove, lift up the lock lever, then with your finger tips, peel up the edge of the suction cup. This will cause it to release from the windshield. Mount works great. TIP: get an assortment of GoPro mount adaptors and extensions for different mounting situations you will inevitably encounter. Good luck...

Q: 4. Can the holder be rotated so that the phone is held in a landscape position for video?

A: The PANAVISE PortaGrip Smartphone Holder With 811 Suction Cup Mount (BH # PAPH811SCM) may be rotated and the side holder arms adjusted for positioning the phone in the landscape/horizontal orientation.

Q: 5. How much weight can this support? Likely attaching it to a stationary, flat, polyurethane-wood surface?

A: The RigWheels C-Cup Suction Cup CC01 can hold up to 40lb depending on application.

Q: 6. What is the ball size, I'm looking for something too swap end connections with?

A: The PanaVise ball of the PANAVISE ActionGRIP Ball-Head Suction Cup Mount for Action Cameras (Double-Knuckle) is 0.815" in diameter.

Q: 7. Anyone have experience with attaching this to a hub cap on a car?

A: The wheel cover must be flat and/or smooth. Then the cap and the suction cup must be immaculately clean and dry. If they are not, the mount will not stay on. This is good only for moderate speeds.

Q: 8. What is the pull rating of this vacuum mount?

A: The information listed for the 9.SOLUTIONS Suction Cup is maximum load from the base. And that is, 4.4 lbs.

Q: 9. Will this model fit most cameras?

A: The GoPro Suction Cup Mount is compatible with all GoPro camera models.

Q: 10. What size is the screw? Is it removable so I can replace it with a longer screw?

A: The screw size is 1/4"-20 and not adjustable.