The Fiberbilt P50 Versatile Mount and Print Shipping Cases 24 x 30", 3.0" Deep (Black) is a polypropylene shipping case with heavy-gauge steel corners designed for transporting and storing mounted or matted prints, pictures or artwork. The case has a full-size cardboard liner to prevent scratching. It uses 1" nylon web quick release straps with buckles to seal the case. The case has a mailing label space and a carrying handle.

For Mounted or Matted Artwork    Heavy-Gauge Steel Corners    Full-Size Cardboard Liner    1" Nylon Web Quick Release Straps    Mailing Label Space    Carrying Handle

• Polypropylene shipping case
• Heavy-gauge steel corners
• Full-size cardboard liner to prevent scratching
• 1.0" nylon web straps with quick release buckles

Mailing label space

Carrying handle

Related Questions and Answers

Q: 1. Since this is an item that is meant to carry an extra lens, how is that accomplished with out an over the shoulder strap?

A: The GoWing Lens Flipper Versatile for Canon RF-Mount Lenses has a 1/4"-20 socket, so it could be carried with camera strap systems that use a 1/4"-20 stud.

Q: 2. Specs say, "Retractable carry handle folds flat when the case is shipped." It's been delivered to me and the handle doesn't look at all retractable to me. How does it retract? I don't want it to break off during shipping.

A: The handle pushes down flat as shown in the 2nd photo.

Q: 3. What are exact exterior dimensions? Need to calculate whether or not this case will get hit with airlines Oversize Checked Bag Fee for exceeding 62 inches (L+W+H).

A: According to the manufacturer the shipping dimensions of the case are 45 x 11 x 12 = 68 . So yes, prepare to pay.

Q: 4. Can this drive use with Macbook pro M1 max 2021 with thunderbolt 4 port?

A: You can use the WD 4TB WD_BLACK P50 Game Drive SSD with a MacBook Pro M1.

Q: 5. This will not fit the 11 inch iPad Pro ?

A: Unfortunately no. The Go Professional Cases EVO II Monitor Mount will only work for 6.5 to10.5" Tablets.

Q: 6. What dead cat will fit the M3? I have the Rode WS3 foam one already, looking for something to use outside.

A: The RODE M3 Versatile End-Address Condenser Microphone (BH # ROM3) will work with the WindTech Fur Fitted Microphone Windshield (B&H # WIMM600). The Mic-Muff on average provides up to 20db of wind-noise reduction in a 20 mph wind, while producing no negative effect on frequency response. Typically, this windshield can be fitted directly over the foam windscreen that came with your microphone or video camera, but some models may require placement over the microphone alone.

Q: 7. 16 3/4" dimension is how much it extends outward from rack ?

A: 16-3/4" is the width of the surface area for the Atlas Sound VTD1-61 Versatile Sliding Shelf and Tray. The shelf slides out and extends 17" outside of the cabinet rails. It mounts in 19" wide cabinets that are 18-1/2" to 25-1/2" deep and equipped with front and rear mounting rails.

Q: 8. Would the medium mirrorless core unit fit the Nikon Z8 with 24-70 f/2.8 attached, and the 70-200 f/2.8 beside?

A: Yes, you can fit your Nikon Z8 Mirrorless Camera with Nikon NIKKOR Z 24-70mm f/2.8 S Lens attached and have enough space to fit your Nikon NIKKOR Z 70-200mm f/2.8 VR S Lens.

Q: 9. How many mounted competition prints can fit in this (depth-wise)?

A: It really depends on the thickness of the board you are mounting the prints to. The case is three inches deep. So best is to figure out which board you are mounting the prints to and see how many can fit in three inches.An example is 4 ply board on an average is about .0610 thick. If you are not matting the prints but just putting the prints on board, divide .0610 inches in to 3 inches. And that is about 49 prints. But the print has thickness so that is just approximate and only if you use 4 ply board.

Q: 10. What are the internal measurements?

A: Fiberbilt by Case Design P50 Versatile Mount and Print Shipping Cases 11 x 14", 2.0" Deep has internal dimensions of 11x14x2 inches.