Water, crush, and dustproof as well as buoyant, this 51.9L, black Nanuk 950 Wheeled Hard Case with Cubed Foamprovides a durable and secure transport and shipping solution for your sensitive and valuable gear. It comes with an egg crate foam lid layer, a solid foam bottom layer, and customizable pre-scored foam layers for the interior. The lid and bottom layers prevent contents from shifting, while the prescored layers can be adjusted to cushion your specific gear.

The case is made from UV-protected NK-7 resin to resist discoloration and material degradation over time while being impact and temperature resistant. It features the patented PowerClaw latching system that uses compressive force to keep the case securely closed until you open it. Integrated slide locks prevent the case from accidental opening, even if dropped, and accommodate user-supplied padlocks for added security. Carry the case using the folding soft-grip top handle or roll it with the retractable pull handle.

NK-7 UV-Protected Resin    2 PowerClaw Latches    IP67-Rated Dust and Waterproof    Impact Resistant and Crushproof    Egg Crate Foam Lid Insert    Automatic Pressure Release Valve    Integrated Lid Stay for Easy Access    Retractable Pull Handle & Wheels    Stackable with Same-Size Cases

• UV-protected NK-7 resin resists discoloration and material degradation
• Interior measures 20.5 x 15.3 x 10.1"
• Lid depth is 2.1"
• Base depth is 8"
• IP67-rated dustproof
• Submersible to 3.3' for up to 30 minutes
• Buoyant up to 110 lb maximum total weight
• Broad operating temperature of -20 to 140°F
• ATA 300 tested to be crushproof and impact resistant
• Automatic pressure valve prevents vacuum seal due to changes in altitude

• Egg crate foam lid insert
• Solid bottom layer
• Prescored cubed layers

• Front grooves interlock with built-in feet at the base for stacking multiple cases of the same size
• Removable lid for 100% unrestricted access to interior

• Soft-grip, foldable, top carry handle
• Retractable pull handle
• Polyurethane wheels

• Accepts user-supplied padlocks
• Patented PowerClaw clamp-latch with slide lock
• Corrosion-resistant stainless steel hardware

Related Questions and Answers

Q: 1. Would gf 100-200mm 5.6 fit in the lens slot?

A: Unfortunately no, the lens would not fit in the pre-cut holes. However, depending on which lenses you are using specifically besides the 100-200mm, you could use the 2500 case instead. It is the same case just without the pre-cut areas: https://bhpho.to/2qhttgd

Q: 2. is the foam pre cut or uncut?

A: The foam in the Nanuk 905 Hard Case for Sennheiser Single XS Wireless Set (Black, 6.3L) is pre-cut, with custom-cut slots for a receiver, a handheld microphone, a transmitter, a charging cable, and accessories.

Q: 3. There is a foam for the bottom and top of the case. Is only 1 of the other two foam layers scored? If so, how do you buy a single scored layer to replace the bottom full foam layer to increase capacity in the case?

A: Both of the two middle layers will be pre scored for easy plucking. And to purchase just one layer individually, you would have to contact Nanuk for that.

Q: 4. Is this cabin friendly size? How many camera and lenses will fit in?

A: This is just slightly larger than the average allowable carry-on dimensions from most airlines. This case's external dimensions listed in the Specifications are: 22.0 x 13.8 x 9.2 in (55.9 x 35.0 x 23.3 cm), while the average airline carrier's approved carry-on bag dimensions are: 22.0 x 14.0 x 9.0 in (56.0 x 35.0 x 22.0 cm), including handles and wheels. It would be up to the airline to allow it on-board or require it to be checked at the gate.

Q: 5. hey looking to see if this would fit a atoms sumo 19 se with the accessories ?

A: Yes, the Nanuk 950 Wheeled Hard Case with Cubed Foam (Olive, 51.9L) can fit the Atomos Sumo 19" SE HDR Monitor, Recorder, and Switcher with it's feet mounted to the monitor inside it. There would also be some room left over for the other parts that are included with the monitor.

Q: 6. What GF lenses will fit in the case?

A: the length of the lenses have to be less than 4.5 inches.

Q: 7. Are there any tutorials on how to design and set up the foam inserts?

A: Nanuk has tutorials posted for the Nanuk Multilayered Cubed Foam Insert for the 910 Case on their vimeo account. You can find the videos here; https://bhpho.to/4d3y3kt

Q: 8. What size to the lock eyelet?

A: Unfortunately, the size of the lock eyelet of the Nanuk 910 Hard Case with Foam (Black) is not specified but it fits regular pad locks such as this one. https://bhpho.to/2FIEXwY

Q: 9. i need interior foam for this case

A: Unfortunately, we do not carry the interior foam for this case separately. In order to have foam for this case, you will need to purchase the HPRC 6300 with foam included: http://bhpho.to/1jnJ1D1

Q: 10. Any idea what trekpak liner size fits this?

A: The Trekpak for the Nanuk 950 Protective Rolling Case would be the "TRP1610CI": https://bhpho.to/2GOoFUy