The titanium SolidDrive SD1G Sound Transducer for Glass Installationfrom SolidDrive SD1G Sound Transducer for Glass Installationutilizes dual-voice coil technology in an aluminum enclosure to transfer acoustic energy to any substrate. Symmetrically opposed neodymium magnets and specifically engineered mounting hardware results in hidden planar-source acoustics. The result is acoustical uniformity throughout the listening space.
This sound transducer is designed for mounting on glass surfaces, and comes with a double-sided VHB (Very High Bond) adhesive silicone disc and a direct screw aluminum mounting base and an attached wiring harness with EuroStyle connector. This transducer can be installed on windows to deliver sound to glass storefronts and glass reception areas. The entire windowpane can become a speaker delivering both interior and exterior sound on a single-pane glass.
The SD1G Sound Transducer is suitable for use at restaurants, mall stores, auto dealerships, department stores, stadium sky boxes, reception areas, and glass atriums.

Dual-voice coil technology in a durable, aluminum enclosure delivering high power handling and sensitivity across multiple substrates

Symmetrically opposed neodymium magnets convert audio signals into acoustical energy for any rigid surface including glass

Hidden planar-source audio technology evenly distributes acoustic energy throughout the listening space

Behind-surface mounting technology ensures maximum visual appeal

SolidDrive Glass Passive Equalization Module (sold separately) increases the transducer's sound performance for optimal listening enjoyment by using notch filters to correct peaks in the frequency response

For extended frequency response, couple this SolidDrive unit with SW7 or SW8 subwoofers (sold separately)

CE, UL 1480 & 2043, and RoHS compliant

Related Questions and Answers

Q: 1. What is/are the difference/s between this subwoofer and this model JBL CONTROL 19CST?Can I connect this subwoofer to regular AV receiver or need another solution to make it works since it's PASSIVE subwoofer?

A: The JBL CONTROL 19CST features a 70-v transformer, appropriate for installation with commercial sound equipment. JBL CONTROL 19CS lacks this transformer, but may be connected to an AV receiver provided the receiver has sufficient output power.

Q: 2. Is this speaker provided with the necessary transformer?

A: It is not included. To ensure optimal listening experience, the installer must equalize the SolidDrive SD1 System. Equalization is accomplished by using the SolidDrive Drywall Passive Equalization Module (sold separately).

Q: 3. If I am to buy this, what other things I need to buy that would work with this? Thanks!

A: Additional Features & Requirements Requires a power amplifier that supports frequencies below 20 Hz, and power output between 75 to 400W. Mounting hardware and speaker wire are also required. Subwoofer Compatible - The ButtKicker Advance can be used with your existing subwoofer. If there is only one output, an optional Y-cable can be used. Thermal Switch - The ButtKicker Advance is set to shut down automatically if it gets too hot in order to prevent damage to the unit. Please note the accessories listed on this product page.

Q: 4. Is there a recommended case or this projector?

A: There are a few hard case recommendations listed under the accessories on the webpage.

Q: 5. Does this only allow me to send the same input to multiple zones or can I run two separate inputs through this to different speakers in multiple zones? I cant read what the output section says but I see the outputs all have different power considerations

A: You can send only the same mix to different zones although you can selectively turn on and off zones.

Q: 6. Thanks, what amp is recommended to drive the 4 buttkicker advance? Is there a way to separately control the intensity of each unit?

A: An amp of 75-400 W. To control separate units, you would have to use separate amps or at least an amp with 2 channels, so adjustments could be made separately. ButtKicker BK4-4 Specs Frequency Response 5 to 200 Hz Nominal Impedance 4 Ohms (inductive) Power Handling Minimum: 75 W Maximum: 400 W

Q: 7. do the speakers get glued to drywall?

A: This sound transducer is designed for mounting on drywall surfaces, and comes with a direct screw aluminum mounting base and an attached wiring harness with EuroStyle connector. This transducer can be installed in-wall and in-ceiling, and patent-pending acoustic in-wall mounting brackets are needed for installation (sold separately).

Q: 8. What transformer is to be used with this speaker?

A: The Solid Drive SD1 is designed for 8 ohm applications. We do not carry transformers for these units. For 70v/100v systems please contact the manufacturer directly toll free 855.663.5600 or sales@a href= http://mseaudio.com target= _blank mseaudio.com/a for support.

Q: 9. Hello Can i control the volume of each zone or set of speakers separately Can i send different music to different zones Thanks

A: To control the volume of each zone, you need to have a separate volume control unit connected to each zone. You can selectively turn on and off zones from the amplifier but you cannot create different mixes for each zone.

Q: 10. Does this work with only AXIS Cameras or is it compatible with any IP Camera?

A: The Axis Communications T8415 Wireless Installation Tool Kit will work with most IP cameras, not just AXIS branded cameras.