The 3.5mm TRS Right Angle to Dual TA5F Y-Cable, 24"from 3.5mm TRS Right Angle to Dual TA5F Y-Cable, 24"is a 24" Y-cable designed to connect the stereo tape output of Sound Devices production mixers to two Lectrosonics transmitters.

This 3.5mm TRS right angle to dual TA5F cable is compatible with the Sound Devices 633 (X3/X4), 664, 688, and 552.

For Sound Devices Tape Out    Connects to Lectrosonics Transmitters    3.5mm TRS Right Angle to Dual TA5F    For L/R Stereo Mix    Length: 24"

Related Questions and Answers

Q: 1. Does this cable have a foil shield?

A: I am sorry but the manufacturer has not provided any information about the type of shielding used for this cable.

Q: 2. does it carry stereo signals through this cord? Thanks;)

A: Yes the Movo Photo MC1 carries stereo signal.

Q: 3. Can this cable connect the output of a Rode Wireless Go 2 Receiver to 2 mono XLR inputs with VXLR, VXLR+ or VXLR Pro adapters?

A: You can use the RODE SC11 Right-Angle 3.5mm TRS Y-Splitter Cable with two RODE VXLR 3.5mm TRS Female to XLR Male Adapters (B&H # ROVXLR), but a simpler and less expensive option would be to use a cable like the Kopul Y-Cable with 1/8" TRS Stereo Mini to 2 XLR Male Connectors - 10' (B&H # KOSMYCM2XM10).

Q: 4. Will this work with a Zaxcom rx200 reciever?

A: Yes, the Cable Techniques CT-LPST5A3M-24 LPS Low-Profile TA5F to Dual Right-Angle XLR3M Y-Cable is compatible for use with the Zaxcom R200 Wireless Receiver which has a TA5 (5-pin mini-XLR) output connector.

Q: 5. Will this cable work in reverse? Stereo output into two mono sources? I want to split the L R output of my Zoom F6 into separate G3 transmitters for a camera hop.

A: Yes, this cable would work in both directions, so you could take a stereo source and separate it in to two mono signals, left and right. .

Q: 6. Will this thread to a sony wireless receiver?

A: This cable will connect to a Sony receivers threaded connector as well.

Q: 7. Tried using with Rode Wireless Go mics, but sounds is only being picked up from one mic (black side). Is there any way to fix this?

A: This cable : Rode SC11 Right-Angle 3.5mm TRS Y-Splitter Cable (10.9") BH #ROSC11 Is a "Mono to Stereo cable". It is designed to take two Mono signals and split them to the Stereo input of a camera If you do not have two, discreet or independent Mono signals, fed into the two 3.5mm connectors, separately, as Mono signals into each connector, you will NOT get both Left and Right to the destination.

Q: 8. Does rode make a version that is not Coiled like the one that comes with rode videomic pro plus

A: Hello John. Rode doesn't currently sell the straight, non-coiled version of the SC2 by itself. If yours is currently broken reach out to your Rode retailer for a replacement under the warranty. If you would like something similar, I have found this third party option, although it's longer: https://www.bhphotovideo.com/c/product/1001074-REG/startech_mu1mms2ra_right_angle_3_5mm_to.html

Q: 9. Will this split a GO 2 receiver into CH1 and CH2 so I can monitor two lavs separately?

A: Yes, the Cable Techniques 3.5mm Right-Angle TRS to Dual Low-Profile TA3M Mini-XLR Y Cable can be used with the RODE Wireless GO II Digital Wireless Microphone System and will split the audio from each transmitter onto separate channels when the receiver is set for stereo mode. Be aware that this cable has TA3 mini-XLR connectors for use with cameras like the Canon EOS C70 or the Blackmagic Pocket Cinema Camera 6K Pro, or other audio devices equipped with mini-XLR mic inputs.

Q: 10. Each of the TA5F ends receives a summed L/R mono - correct? Just confirming this does NOT separate left from right.

A: The Cable Techniques CT-P35RLT2-24 DOES in fact split left and right channels between the two TA5 connectors. The purpose of the cable is to enable transmission of a L/R stereo mix from a 3.5mm source.