The Chief Fusion CAT5 Surge CPU Adapteris designed to allow you to install a surge protector, CAT5 converter, media player, small CPU, or Chief PACPC1 Power Filter behind your screen mounted with a Chief FUSION-series fixed or tilt mount. It will fit equipment up to 1.8" in depth. The FCA110 adds zero depth to your installation and is TAA compliant.

Accepts CAT5 Converter or Media Player    Accepts Small CPU or Chief PACPC1 Filter    Adds Zero Depth to Installation    TAA Compliant

Related Questions and Answers

Q: 1. unit weight?

A: the unit weight is 19.80 pounds and will support up to 125 pounds.

Q: 2. This is good with MSI MPG Z790 EDGE WIFI DDR4 LGA 1700 ATX Motherboard and Intel Core i5-13600K. ? Thank you. Jean-Jacques

A: The Noctua NH-U12S CPU Cooler is compatible with LGA 1700 socket CPU.

Q: 3. Will this work in Cuba?

A: Yes, this will work in Cuba.

Q: 4. Are the dimensions listed internal or external? I am looking to make sure it holds a 2021 Samsung frame tv box. Thanks

A: The listed dimensions for the Chief PAC525 In-Wall Storage Box is the external size.

Q: 5. is this fan compatible with the gateway dx4860 motherboard?

A: That computer uses a LGA1155 socket. The fan supports that socket.

Q: 6. Can this work on LGA 1200 socket? I am planning to use it for i-5 11th Gen. Please let me know

A: No - per the Overview, "Compatible with Intel LGA 1156, 1155, 1150, and 1151 sockets..."

Q: 7. Is there a template for mounting

A: NO! Completely unnecessary! Figure the center of where you want the tv, left,right and up,down and mark it with a pencil. Before removing uprights spread them out to max and that is the most they can be mounted apart from each other on the wall. I would subtract an inch to avoid problems. Ideally you want to mount them 22-26 inches apart at the same height. It is all dictated by where your studs are located. Just dont mount to close together, less than 16 inches apart you best keep it centered all the time. Remove the uprights from the crossbars. You can use the same upright to mark both sets of holes. Your template. Use hardware capable of bearing the load(250lbs). If they are mounted at different heights as long as not to much. Half inch or so. There are screws at the top of each to level the bars perfectly. This is probably the BEST TV stand for sale anywhere! GOOD LUCK!!!

Q: 8. Does this unit come withe the flange and cover kit as shown in the picture, or only the box?

A: The Flange and Cover are not included. Instead you would need B&H # CHPAC525FC which is the same box with the Flange and Cover included. https://bhpho.to/2YZRg0u

Q: 9. How doest it PASSIVELY convert analog to digital and vice versa?

A: There is no Analog to Digital conversion on the SoundTools CAT Rack FX Audio Over CAT5 Rack. This unit is effectively a snake that uses CAT 5/6/7 ethernet instead of a multichannel copper cable. It can accept and send both Analog and Digital (AES/EBU, DMX. Etc) signals in the same CAT5/6/7 Ethernet cable.

Q: 10. can I get a box configured with both XLRF & XLRM connectors?

A: The SoundTools CAT Rack FX Audio Over CAT5 Rack is only available as shown with the 12 XLR 3-pin female connectors and the SoundTools CAT Rack MX Audio Over CAT5 Rack is only available with the 12 XLR 3-pin male connectors. However, you can create a custom rack-mounted stage box by combining the two models or you can contact the manufacturer directly to inquire about ordering a custom build, which they do offer upon request. As another option for consideration with both male and female XLR connectors and CAT5, you may like the SoundTools WallCAT WC851-B Two-Gang Wall Plate with Four Male & Four Female XLR Connectors (B&H # SOWC851B). You can reach SoundTools by email at support@soundtools.com or contact them by phone at 805-383-0777.