Dedicated to the moving dolly for boxes or appliance650-EX, TH-X, and TH-Z tripod systems, the moving dolly for boxes or applianceoffers increased mobility for repositioning your tripod and can also be used for taking dolly shots on smooth, hard surfaces. Each 3" caster wheel incorporates its own foot-activated lock for increased stability, and the dolly supports loads up to 80 lb. Additionally, it folds down for easy carrying via the integrated handle.

Fits 650-EX, TH-X & TH-Z Tripod Systems    80 lb Load Capacity    Individual Wheel Brakes    Folds for Transport    Integrated Carry Handle

Libec 650EX Tripod System with Mid-Level Spreader (65mm Ball) 650EX

Libec TH-X Head and Tripod System TH-X

Libec TH-Z Tripod System with Mid-Level Spreader (75 mm) TH-Z

Libec TH-Z T Aluminum Tripod with Mid-Level Spreader (75mm Bowl) TH-Z T

Related Questions and Answers

Q: 1. Are there 2 separate outputs on this encoder?

A: This encoder has both an SDI and HDMI output.

Q: 2. How thick is the plywood on the tops of these boxes?

A: It is 0.5 on all sides

Q: 3. Will this power the lights at full brightness? Unlike other adapters I have tried which are 12v5a and only power the lights to about 50% brightness..?

A: Yes, this adapter should power the compatible lights of the YN600, YN600II, and YN300AIR to full brightness.

Q: 4. Is this compatible with the Yongnuo YN6000 Bi-Color LED Panel?

A: Yes, this power supply is compatible.

Q: 5. How many QuadHead2Go devices do I need to connect 8 monitors to a single input? 2 or 3?

A: To connect 8 monitors using the Matrox QuadHead2Go Multi-Monitor Controller Appliance, you would need 2 units, but you would also need 2 DisplayPort outputs from your source in order to connect to 8 monitors. Matrox recommends using a Luma Series graphics card such as the Matrox Luma Series LUMA A380 Graphics Card, BH #MALUMAA380 to connect multiple appliances.

Q: 6. This power supply is In the related products for yongnuo YN360. It says it's compatible but it is a 12v 5A power supply. On my YN360 it's written 8v 5A. I'm confused...

A: This power supply is rated for up to 12v and has been tested and approved for the YN360.

Q: 7. Can these be used for the Dana Dolly? At what height would be recommended?

A: Hi Matt. Normaly doing things under the camera is another department, another profession. But when you'll use it, you should use bar clamps if you want to add / stack the boxes. It can be a slippery business sometimes. Make sure that nothing can move sidewards by accident. Dirt, dampness can act like lubrication. The weight will never be a problem, the boxes can hold easily a magnum dolly carrying to person. Safety first, you should think and always have wooden wedges with you. Have educated and experienced crew members around you, if possible. You would need a lot of the big boxes to support your Dana dolly on both sides, wouldn't you? I personally would go to a meter hight with no problems, like I said, using clamps to make it solid. Instead think about using a ladder on both sides, or a kind of foldable platforms. I hope I could answer your question to your satisfaction. Good luck for all your shooting situations.

Q: 8. Hi, Is this AC Power Adapter is compatible to the following Adapter listed? AC Adapter 5V-12V 12V 1.5A, 5.5/2.1mm, US 2-Pin Plug Thanks

A: This Powers Select Yongnuo LED Lights. We are not aware of its capabilities beyond that.

Q: 9. Is the circular connector inner diameter 2.1mm or 2.5mm? Is the outer diameter of it 5.5mm?

A: After speaking with the distributor, the link power adapter inner diameter is 2.1mm and the outer diameter is 5.5mm.

Q: 10. What is the cable length?

A: The cable is around 5 to 6 feet long.