Patterns, or gobos, are widely used by designers in theatre, film, photography and television to create atmosphere, project scenery, and generally enhance the visual impact of their lighting.

Conceived by some of the world's leading lighting designers, the Rosco range presently includes hundreds of standard steel gobo designs.

To insure design integrity the patterns are etched using a precise double-sided process on stainless steel. The result is durable, high quality patterns which will withstand the extreme heat at the gate of ellipsoidal spotlights.

Rosco steel gobos are round to allow for rotation in the gate when aligning the projected image.

The standard "B" size is suitable for most fixtures with a 6" lens when used with a Rosco Pattern Holder or the holders of other manufacturers.

Trimming of patterns, where necessary, can be easily accomplished with a pair of scissors.

Related Questions and Answers

Q: 1. Is the inside 1-3/8" in diameter? If not, is any part of it 1-3/8" in diameter?

A: The diameter of the Ultimate Support 13763 Pole Size Adapter is 1.5" (38 mm) to fit on the Ultimate Support TS-80B, TS-80S, TS-88B, TS-90B, TS-99B, TS-99BL, TS-100B, TS-110B, and TS-110BL speaker stands and adapter them to accommodate the 1-3/8" (35 mm) pole cups that are commonly used on many speakers.

Q: 2. What is the optimum distance or range for this projector? Does it have a zoom feature?

A: While this light lacks a zoom feature, its optimal range is within 1 meter from the subject.

Q: 3. What is the overall length (end-to-end) of this part?

A: The length of the Ultimate Support 13763 Pole Size Adapter is 8.5".

Q: 4. Is Crystal gel non-flammable?

A: According to the manufacturer, the Rosco CrystalGel - 1 Gallon, is water-based, so it is not flammable. However, it is still not considered to be flame-retardant when it is dry,

Q: 5. Does this fit b-size gobos?

A: No. The following unit adapts to gobo size 26.8mm

Q: 6. How far should I mount it away from the wall with a good brightness?

A: The manufacturer does not list a specific distance at which the American DJ Gobo Projector IR should be placed. However, thy do state that at a distance of 3 meters (or 9 feet 10 inches), the LUX output power 9brightness) would be approximately 540 Lux.

Q: 7. when i go and try and purchase a Gobo the size they offer is 26.8mmODx24mmIA is that the same as 26.8mm viewable size 24mm?? for this ADJ projector?

A: the actual gobo size is 26.8mm. The viewable size after installed is 24mm. The gobo maker should specify it is for this fixture.

Q: 8. How can I get a remote for this particular projector?

A: To remotely control the American DJ Gobo Projector IR, you can purchase the American DJ IR Remote for Inno Pocket Spot (B&H # AMUCIR).

Q: 9. Does anyone have experience using this? I am curios if the mount has any play after pinned into place, will the monitor wiggle at all? The pin looks like it will hold the monitor in its locked position but does it do this without play?

A: Yes. Please contact our live chat team for more support.

Q: 10. I love this cutter but how do you replace the razor blade?

A: 1-put finger under ribbed portion of sliding blade holder top and pull up. As it swivels (rotates) up it will expose blade2-Slide plastic holder of blade at top side of blade over,3- grab blade from top protected end and pull it strait up and out of holder.(it slides out sideways)4-slide new blade in exactly in reverse of how you pulled old blade out.5-slide plastic holder back over new blade top holding it in.6- Swivel (rotate)top of sliding blade holder back down into position and your ready to go.7- once you know how to do it the whole process takes ten seconds.