The elation stage light controllerfrom elation stage light controlleris a polycarbonate sheet that can be cut to the size of any light fixture whose beam you'd like to change. For example, you can smooth or widen out any LED Panel or PAR, while also improving the field of color.

Shapes Beam to Your Desired Effect

Related Questions and Answers

Q: 1. Is this only for LED lights?

A: The ADJ Stage Pak 1 Controller & Dimmer Pack System can be used for tungsten lamp heads as well as long as they do not exceed the 1800 watt limit on each dimmer pack.

Q: 2. What is the maximum width of a material that this can be clipped onto; can it be clipped onto 1/2" thick wood? Alternatively, is the weight of the battery pack enough to hod it sitting upright on a flat surface on its own?

A: The clip opens to about two inches. It would be more stable if it were clipped to something,

Q: 3. Will this work with a Chauvet DJ DMX-4LED 4-Channel Dimmer Pack?

A: Yes. If the lights you own do not have built-in DMX, then you may use the CHAUVET DJ DMX-4LED 4-Channel Dimmer Pack with the Elation Professional SDC12 12-Channel Basic DMX Controller for your usage needs, allowing you to adjust the light output from the ground.

Q: 4. What about a case for the controller? I see it seems to have rack mounting ears but there don't eem to be any clues as to the size and kind of case it might best use?

A: We recommend using a case like the Gator Cases GRR-6L Roller Rack Case, which offers lightweight but heavy duty design and wheels for easy transport. Please see the image below.

Q: 5. Does this come with mounting hardware?

A: It comes with brackets and magnet mount options. Clamps not included.

Q: 6. Can both dmx outputs be used at the same time? JJ

A: No, only use one dmx output at a time on the Elation Professional SDC12 12-Channel Basic DMX Controller

Q: 7. Im new to DMX controllers. How does this control multiple lights with only one or two outputs?

A: The idea with DMX512 is to have one cable run (from controller into first light and out from 1st light into second light and out of second into 3rd etc. So that would explain the single output. The SDC12 is used for very basic either testing of units or simple manual control over the fixtures via the faders essentially sending a signal to lights from0-100% activating the features of the light being controlled. If used with an RGB color mixing pars in 3 channel mode fader one for example would dim the R or red channel from 0-100% the second fader would control Green and third control Blue allowing you to mix these colors producing different colors mixing the colors at different levels. For a programmable controller you may want to look at the ADJ DMX Operator. I hope this helps?

Q: 8. I have tested with just the only dmx light I have--it works but ony using the #1 slider--can't seem to assign the light to another slider. I'll be getting more dmx lights, so how can I assign lights to the other sliders? (If adjust the light itself to channel 2, I can still only control it with the #1 slider, and I didn't have any luck messing with the dip switches on the controller--I didn't fully understand their explanation of the switches.)

A: If you set the light's DMX address to one more than the address of the controller then it'll be able to be dimmed with slider #2. Set the light to two more than the address of the controller and you can use slider #3 to adjust it, and so on.

Q: 9. does this work with FotodioX Pro FACTOR 1 x 2 V-4000ASVL Bi-Color Dimmable LED Studio Light?

A: The system referenced is made for conventional par lights and would not be ideal for what you are likely trying to do. This setup is for units without an internal dimmer such as a 500 watt Par can. The unit that you refer to states that it is controllable via dmx but I cannot seem to find how many control channels it uses, so I would assume one and its just for dimming although the color temp seems to be adjustable also so it may be more channels. I would ask B and H about that part. I would recommend the SDC12 if you just want manual control of the dimming and no programming or scene recall. The description refers to DMX as the control source and also that it is 3 pin so there isn't any reason I can think of that this controller wouldn't work.If you want programability I recommend something like the ADJ DMX Operator or the Elation Show Designer 1 for more intricate programming.

Q: 10. Will this work with the Litepanels DMX module? I'm planning on using two Astras in a studio grid setting.

A: Yes it will work with the 5 pin DMX512