Designed to eliminate the extra step of finishing the screen with trim, the 220V automatic projector screen ceilingfrom automatic projector screen ceilingis designed with ceiling trim already in place. Once the screen is installed, the screen's trim conceals the rough opening eliminating the need to complete additional trim work. Sliding installation brackets are included to make it easy to attach the screen housing to the structure above the drop ceiling.

The Advantage Electrol screen features simple in-ceiling installation that can be done in two stages. The screen case can be installed during the rough-in construction stage and the fabric assembly can be completed during the finishing stage.

137" Diagonal / 16:10 Aspect Ratio    Cinema Vision Screen Finish    1.3 Gain / 90° Viewing Angle    Slim-Tab Tensioning System    White Powder-Coated Case    Installs Above the Ceiling    Black Backing Standard    Silent Motor    Low Voltage Control (LVC)

Cinema Vision is designed to provide a higher amount of brightness for lower output projectors. Its increased reflectivity enhances brightness in situations where a moderate level of ambient light is present. Ideal for video images. Cone: 90° Gain: 1.3

• Smooth Roll Technology to keep your screen flat
• Slim-Tab, a lower profile and stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension

• UL Plenum rated case
• White powder-coated case for a clean aesthetic
• Black-backed screen material for enhanced image quality and opacity
• Seamless surface

Designed to provide silent operation when raising or lowering the screen

Allows the included wall switch, as well as devices such as automation systems, third-party wall switches, and remotes that support LVC, to raise or lower the screen remotely

Related Questions and Answers

Q: 1. Can the "micro 4/3" 16 mm extension tube be fitted with the Olympus MC-20 (even if not recommended)? Stated differently: Will the protrusion of the MC-20 fit inside the extension tube?

A: Using a teleconverter with an extension tube is not recommended.

Q: 2. Will these work with an EM1 Mkii AND the 60mm OLY macro? Tx.

A: Yes, the tube will work with the EM1 and the 60mm macro.

Q: 3. if i connect 4 mics, can it allow 2 mics to be 'on' at the same time? (i.e. 2 different talkers), or the 'MaxBus' will strictly limit it to 1 mic at a time only?

A: The Shure SCM410 allows you to connect and use up to four microphones at the same time.

Q: 4. What is the maximum wattage if converting from 110v to 220v? (I am in North America with an EU product).

A: The specs says the maximum wattage for the Sevenstar AR-5000 Automatic Voltage Regulator is 5000 W

Q: 5. Will this work with Olympus omd em10 Mark II?

A: Yes, it is compatible with the EM10 mk2.

Q: 6. Will the mixer automatically set the microphone sensitivity? And does it have a limiter?

A: You will have to initially set the mic levels. Then it will open the mic when someone speaks. Yes it has a limiter. A Multi-pin Logic connection provides Mute, Gate and Override remote control options.

Q: 7. Will this viewer work with glass mounted 2 slides?

A: This is a nice little projector but I only tried regular slides in it. I do not know if glass-mounted would work.

Q: 8. Can the Sheet Feeder be left on the plotter or does it have to be removed, when plotting on the 24" roll ?

A: The Auto Sheet Feeder T200 does not need to be removed when printing on a roll. . It allows you to send to print multiple sheet sizes (A4/A & A3/B) without manually switching the media source (sheet to roll).

Q: 9. Is it possible to disable the 12v phantom power?

A: Yes. There are 4 numbered DIP switches on the back of the unit. To disengage the phantom power, simply flip the right-most switch numbered "4" into the down position, and the phantom power will turn off.

Q: 10. Will it cancel noise from ceiling speakers if I have the mx393 omnidirectional microphone?

A: Thank you for your question. This mixer does not have any noise canceling capabilities. You would need to find the best position for the microphone in the room for the least amount of possible feedback and ambient noise