Patterns, or gobos, are widely used by designers in theatre, film, photography and television to create atmosphere, project scenery, and generally enhance the visual impact of their lighting.

Conceived by some of the world's leading lighting designers, the Rosco range presently includes hundreds of standard steel gobo designs.

To insure design integrity the patterns are etched using a precise double-sided process on stainless steel. The result is durable, high quality patterns which will withstand the extreme heat at the gate of ellipsoidal spotlights.

Rosco steel gobos are round to allow for rotation in the gate when aligning the projected image.

The standard "B" size is suitable for most fixtures with a 6" lens when used with a Rosco Pattern Holder or the holders of other manufacturers.

Trimming of patterns, where necessary, can be easily accomplished with a pair of scissors.

Related Questions and Answers

Q: 1. How many inches/cm wide do the jaws open?

A: The clamp opens to 2.3".

Q: 2. How do you switch from haze to fog and back to haze?

A: The Rosco V-Hazer Fog Machine BH #ROVH outputs fog or haze based on the type of fluid used.

Q: 3. Is the 220v version the same exept the fuse and the power plug?

A: Yes the only difference between the 120V and 220V is the plug and the fuse.

Q: 4. Is this compatible with American DJ water based fog machines?

A: Yes this fluid would be compatible with water based fog machines by American DJ.

Q: 5. How far should the ridged top lift in order to remove the blade? Mine is only about 45' open and the blade isn't accessible. I'm afraid that the blade has shifted and is causing it to not be accessible. I would love to see a video of this process. I love this cutter, but need to replace the blade!

A: I would recommend contacting Falcon; Falcon (Marshall)Distributed By - Omega BrandessTel: (410) 374-3250 Website http://www.omegabrandess.com/ Email customerservice@omegabrandess.com

Q: 6. What material is this tool made out of? Is it aluminum? The package weight is only 1 pound.

A: Falcon (Marshall) Personal-Size Paper Cutter is made out of an assorted composition of steel.

Q: 7. Is the inside 1-3/8" in diameter? If not, is any part of it 1-3/8" in diameter?

A: The diameter of the Ultimate Support 13763 Pole Size Adapter is 1.5" (38 mm) to fit on the Ultimate Support TS-80B, TS-80S, TS-88B, TS-90B, TS-99B, TS-99BL, TS-100B, TS-110B, and TS-110BL speaker stands and adapter them to accommodate the 1-3/8" (35 mm) pole cups that are commonly used on many speakers.

Q: 8. Do i need to buy kupo grip head seperatly?

A: You will need a grip head to attach it to a stand https://bhpho.to/2IVmajI.

Q: 9. Does the maximum load of 11 pounds include the counterweight? Or is it 11 pounds on the extended end, and then the counter weight is in addition to that?

A: I've personally used it to arm out a Kino Diva 401 with a 15lb sandbag on the back. As long as it's rigged correctly at the knuckle, I'd say the 11lb weight limit is an engineers rating. That being said, a weak point is definitely swivel counterweight hook on the back. I've not taken it apart to see how it's attached, but it can't be very secure as it swivels to prevent weights from falling off. However the real weak point is the operator. Putting 1lb out at full extension can still severely hurt someone if it's not rigged correctly, regardless of the brand of boom. Always use common sense over manufacturers recommendations.

Q: 10. I love this cutter but how do you replace the razor blade?

A: 1-put finger under ribbed portion of sliding blade holder top and pull up. As it swivels (rotates) up it will expose blade2-Slide plastic holder of blade at top side of blade over,3- grab blade from top protected end and pull it strait up and out of holder.(it slides out sideways)4-slide new blade in exactly in reverse of how you pulled old blade out.5-slide plastic holder back over new blade top holding it in.6- Swivel (rotate)top of sliding blade holder back down into position and your ready to go.7- once you know how to do it the whole process takes ten seconds.