Save desk space and position your monitors just where you like them with the articulating dual arm computer monitor desk mountfrom Mount-It!. This full-motion desk mount features 15 degree monitor tilt and 180 degree swivel capability at multiple points for fine-tuning monitor positioning. The height of the monitors can be adjusted up and down the monitor pole. The monitors can be installed in portrait or landscape mode, and can be rotated at any time. In addition, the monitor arms can rotate 360 degrees around the pole.

The aluminum mount will fit most flat-panel monitors no heavier than 22.0 lb and up to 27" in size that are fitted with a 75 x 75 or 100 x 100 VESA pattern. No drilling is required; the mount attaches with a secure dual c-clamp mechanism to any desk or work surface between 0.5 to 4" thick. Cable management under the arms keeps your cables controlled and untangled. All hardware needed for installation is included, as are setup instructions.

Mount 2 Monitors Above Your Desk    Fits Flat-Screen Monitors up to 27"    ±15° Tilt, 180° Swivel    Rotate 360°, Portrait to Landscape    Compatible with VESA 75 x 75 & 100 x 100    Attaches via Dual C-Clamp Mechanism    Cable Management    Frees Up Valuable Desktop Space

Related Questions and Answers

Q: 1. Will this work with two ASUS VE247H 23.6 Full HD 1920x1080 2ms HDMI DVI VGA Back-lit LED Monitors? I've never mounted a monitor before, and I see there is a plate, how do I know what it will fit?

A: Not all monitors are mountable . The ones that are have a clear noticeable 4 holes on the back of the monitor which are standard for any mount. The mount is screwed onto the back of the monitor via these 4 holes. Non-mountable monitors have a clean back with no holes and need to be used with a stand. This particular mount will attach to any mountable monitor. Your investigation should be whether or not these Asus monitors are indeed mountable . Hope this helps.

Q: 2. Can you adjust 2 monitors in a stacked method (top and bottom)?

A: Depending on the size of the monitors you might be able to. There are mounts specifically made for this style mounting.

Q: 3. I have a 27 , 19.4lbs. monitor attach to this stand. No matter how much I tighten the retaining bolt, the monitor always sags downwards. How can I keep my monitor held upright with this system? Thanks.

A: I have the same exact issue with my 24 inch monitor that is attached to the right side. Left side is perfect but ride side sags down ever so slightly. I have accepted it as is. Very weird.

Q: 4. Does this work with Sony fs7

A: Yes.

Q: 5. I am building a custom desk and want to know how much clearance I should leave in the back in order to use this mount. Would two inches be enough? I Plan to have a crossbar run along the back of the desk but I want to have it be far enough into the desk for this to fit

A: I agree with Dany D. below, 3/4 is enough, 1 to be safe.

Q: 6. Are the screws for securing monitor to arms included?

A: Yes - everything is included

Q: 7. Do both monitors need to be the same size and weight?

A: The Mount-It! MI-2762 Dual-Monitor Desk Mount BH #MOMI2762 will support two 13 to 32" displays. They can be different sizes on each.

Q: 8. Can this be mounted on a glass desk?

A: The K&M 23875 Dual Monitor Desk Mount BH #KMDVMDMB could be mounted to a fully-tempered, impact resistant glass desk

Q: 9. What's load capacity per arm?

A: The Mount-It! Dual Monitor Desk Mount with Mechanical Springs BH #MOMI2672 has a weight capacity of 17.6 lbs. per arm

Q: 10. How close can you get it to the wall? Specifically how much distance is there between the last joint and the mounting bracket?

A: Using the Ergotron LX Desk Mount Monitor Arm (White), you could potentially mount a monitor about 3-4" away from a wall.