Designed to eliminate the extra step of finishing the screen with trim, the 220V bedroom ceiling projector screenfrom bedroom ceiling projector screenis designed with ceiling trim already in place. Once the screen is installed, the screen's trim conceals the rough opening eliminating the need to complete additional trim work. Sliding installation brackets are included to make it easy to attach the screen housing to the structure above the drop ceiling.

The Advantage Electrol screen features simple in-ceiling installation that can be done in two stages. The screen case can be installed during the rough-in construction stage and the fabric assembly can be completed during the finishing stage.

bedroom ceiling projector screenThis screen does not include a box, and is designed for installations where a box has previously been selected. Please ensure the box you are using is compatible - i.e., is of the same size and has the same option - as with this fabric, roller, and motor assembly. The box that goes with this model number is: 70115EBLS.

137" Diagonal / 16:10 Aspect Ratio    Da-Mat Screen Surface    1.0 Gain / 120° Viewing Angle    Slim-Tab Tensioning System    White Powder-Coated Case    Installs Above the Ceiling    Black Backing Standard    Fabric, Roller, Motor Only    Silent Motor    Low Voltage Control (LVC)

Da-Mat is a unity gain vinyl surface with a smoother surface than the Matte White finish. It features a white surface for good color reproduction for environments with controllable ambient light. Cone: 120° Gain: 1.0

• Smooth Roll Technology to keep your screen flat
• Slim-Tab, a lower profile and stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension

• UL Plenum rated case
• White powder-coated case for a clean aesthetic
• Black-backed screen material for enhanced image quality and opacity
• Seamless surface

This screen comes with the screen fabric, roller, and motor only, meaning the box must be purchased separately. This design allows the box to be installed during the construction phase while the screen can be installed later, once construction is complete. This ensures the screen won't be damaged during construction

Designed to provide silent operation when raising or lowering the screen

Allows the included wall switch, as well as devices such as automation systems, third-party wall switches, and remotes that support LVC, to raise or lower the screen remotely

Related Questions and Answers

Q: 1. What is the minimum acceptable impedance for the speaker output. (Can I connect four 8 ohm speakers?)

A: The Sonos Amp 2.1 allows for two speakers up to 125 watts at 8 ohms, plus a subwoofer to be connected. In order to connect four speakers, you would run them in parallel, two on the left and two on the right, and each speaker would operate at 4 ohms. The total wattage the speakers should require is 125 watts per side. So each speaker should be rated 60 watts or under at 8 ohms, in order for this amp to power them safely.

Q: 2. If this attaches to the ceiling joist then how do you run the cables into the ceiling? Wouldnt the circular hole be blocked by the joist?

A: You may have to drill some holes. If you were mounting above ceiling tiles, the cable could exit before the joist.

Q: 3. Can I use my Bose 161 speakers with this amp as they are rated at a max of 100w?

A: You are able to use it, you just would not want to turn the volume at max. This could then blow out the speakers.

Q: 4. Can the Sonos amp be used with powered speakers?

A: The Amp unfortunately does not have a RCA Audio Output, only Input. It is only able to be connected to Passive Speakers via Speaker Wire.

Q: 5. Are these speakers wireless?

A: No they are not. These are passive, wired speakers which draw the audio signal and power from the SONOS AMP component.

Q: 6. I am looking for a solution that will allow me to point my projector straight down onto a table. Will this bracket allow this?

A: The Kupo Universal Projector Mount (BH # KUKD303112) will allow for flexible 360 degree and vertical orientation with laser or LED projectors.

Q: 7. What type of fabric does this use? Muslin or poly?

A: This background uses a muslin fabric.

Q: 8. We have a Samsung TV with Sonos Beam and would like to add two un-powered, wired speakers to create surround sound and to stream music. Would this amp work?

A: Yes, this is what you would use for your particular set up.

Q: 9. can I use my Music Hall 5.1 turntable directly into this unit? So the Q is... does the AMP have phono pre-amp?

A: No, this amplifier does not have a phono stage pre-amp. You would need a dedicated phono preamp. Music Hall makes some very high quality ones to go with their turntable. Such as, the Music Hall Bellari vp130 mk2 Tube Phono Preamp with Headphone Amplifier for Moving-Magnet Cartridges. https://www.bhphotovideo.com/c/product/1483524-REG/music_hall_vp_130mk2_tube_phono.html

Q: 10. Would this be sturdy enough to hold a roll of seamless paper?

A: These are designed to be used with the Impact Varipoles. The Varipoles support the actual weight of the roll.