For larger venue installs, the 120V sapphire in ceiling projector screen(fabric, roller, and motor available separately) from sapphire in ceiling projector screenis designed to eliminate the extra step of finishing the screen with trim. The Advantage line of projection screens is designed with ceiling trim already in place. Once the screen is installed, the screen's trim conceals the rough opening in the ceiling, eliminating the need to complete additional trim work. Sliding installation brackets make it easy to attach the screen housing to the structure above the drop ceiling.

Tensioning is provided to help ensure the smoothest surface possible.

sapphire in ceiling projector screenThis box is part of a system. To complete the system you will also require the fabric, roller, and motor assembly. Purchasing the box first allows the box to be installed during the "rough-in" phase of construction. The screen and other components can then be installed once construction is complete. Please be sure to select the fabric, roller, and motor assembly with the exact size and feature as designated by this box. The fabric, roller, and motor that goes with this model number is: 24719FL.

220" Diagonal / 16:9 Aspect Ratio    HD Progressive 1.3 Surface    1.3 Gain / 150° Viewing Angle    Smooth Roll Technology    Slim-Tab Lower-Profile Tab Design    Installs Above the Ceiling    Box Only (No Screen Fabric)    Low Voltage Control (LVC)

Ideal for applications where projector brightness and screen size require an increase in gain, the white surface offers high-fidelity color reproduction, and allows for more flexibility with ambient light conditions. This surface works for video as well as charts and graphs in a corporate setting. Cone 150° Gain: 1.3

• Smooth Roll Technology to keep your screen perfectly flat
• Slim-Tab, a lower profile and stronger tab design to keep your screen perfectly taut
• Tensioning Cable System to prevent warping and ensure even lateral tension

• Standard Low Voltage Control (LVC) to keep your screen operation flexible
• UL Plenum rated case
• Decora-style, three-button wall switch
• Standard black backing retains projected brightness on front projection surfaces
• Seamless screen surface

Related Questions and Answers

Q: 1. Will this fit atomos shinobi? I read that they are the same screen but the shinobi doesn’t have the recorder.

A: yes it will fit the Shinobi.

Q: 2. What is the size when folded and placed in the carry bag?

A: The size is approximately 36.0 x 35.0 x 5.0".

Q: 3. If this attaches to the ceiling joist then how do you run the cables into the ceiling? Wouldnt the circular hole be blocked by the joist?

A: You may have to drill some holes. If you were mounting above ceiling tiles, the cable could exit before the joist.

Q: 4. can I use my Music Hall 5.1 turntable directly into this unit? So the Q is... does the AMP have phono pre-amp?

A: No, this amplifier does not have a phono stage pre-amp. You would need a dedicated phono preamp. Music Hall makes some very high quality ones to go with their turntable. Such as, the Music Hall Bellari vp130 mk2 Tube Phono Preamp with Headphone Amplifier for Moving-Magnet Cartridges. https://www.bhphotovideo.com/c/product/1483524-REG/music_hall_vp_130mk2_tube_phono.html

Q: 5. Are there wider feet available for this product? These are small and not ideal for floors/ceilings that are not perfectly flat.

A: Unfortunately, there are no wider feet available for this product.

Q: 6. What is the minimum acceptable impedance for the speaker output. (Can I connect four 8 ohm speakers?)

A: The Sonos Amp 2.1 allows for two speakers up to 125 watts at 8 ohms, plus a subwoofer to be connected. In order to connect four speakers, you would run them in parallel, two on the left and two on the right, and each speaker would operate at 4 ohms. The total wattage the speakers should require is 125 watts per side. So each speaker should be rated 60 watts or under at 8 ohms, in order for this amp to power them safely.

Q: 7. Looking to use these in a small room for holding both backdrops and seamless (seamless no longer than 5') will this support it safely?

A: Yes two of these poles with the appropriate hardware can support seamless paper and backgrounds that are no longer than 5 feet wide.

Q: 8. Is this compatible with Optima W316ST?

A: Depends if you're projector mount has a 1.5 NPT threaded pipe as an attachment. This product is not a projector mount but rather a plate that attaches to the ceiling from which you can attach a standard pipe extension.

Q: 9. Where do I put the image i want to trace?

A: Hey Joey, I just got an email from B&H asking to help answer your question. We have set ours up and tested it and it seems to work well. There is a opening underneath, where the mirror and light bulb go. Lay your image on your flat surface, and possibly under a small pane of glass to hold it down flat. Position the projector with the opening on the bottom directly on top of your image. I have a 100x equivalent CFL bulb in ours. In a darkened room it should work fine. Also the front tube for focus, the instructions say turn to change focus, but really what you do is slide it out or in depending on the throw length to your canvas or wall you are projecting onto. Hope this helps

Q: 10. Will this fit the atomos ninja plus

A: Unfortunately, the Ninja V Plus has a larger screen size than the Atomos Ninja V.