The Lectrosonics A170AC VHF Antenna with BNC Connectorfrom Lectrosonics A170AC VHF Antenna with BNC Connectoris a VHF replacement straight whip antenna that has a right-angle BNC connector. The antenna is 14" in length and designed for use with Lectrosonics microphone systems.

For Lectrosonics Microphone Systems    VHF Frequency Block    Right-Angle BNC Connector

Related Questions and Answers

Q: 1. Is this Hosa BNC cable 50 Ohm ?

A: Yes this one is. One way to identify it as 50 ohms is by the presence of the white dielectric material in the connector.

Q: 2. What exactly do I need to connect the SNA600A to my Lectro src dual receiver? Do I need both the BNC cable and an adapter?

A: The Lectrosonics SNA600a Adjustable Dipole Antenna uses a 50 Ohm BNC connector to interface with the host device.

Q: 3. Is it compatable with shure axient?

A: No, the Shure UA860SWB Passive Omnidirectional Antenna is not compatible for use with the Shure Axient series wireless receivers.

Q: 4. Is this cable RG-58 or RG-213?

A: The Hosa Technology BNC to BNC Antenna Cable is RG-58.

Q: 5. How does it takes its power ? And can I use it with Panasonic camera model AG-HPX500P ?

A: The antenna is made by Shure and will only work with Shure products. The Shure systems it will work with are the SLX, ULX, UC, UHF, and UHF-R wireless systems.

Q: 6. I have 3 411a being fed via smda's and smqv's and 2 sets of LT/LRs. They're all different blocks from 470 to 22. Would two of these work for all of my sets at the same time if I used a splitter? Or do I have to get two for each band?

A: Hello. This is Nick at Lectrosonics Tech Support. The SNA600a has an effective bandwidth of approximately 100MHz, 50MHz above and 50MHz below the center frequency that you set by adjusting the length of the antenna's arms. However, the sensitivity rolls off gradually above and below the +/- 50MHz points. The SNA600a measures less than 2:1 SWR (Standing Wave Ratio) from 465-850 MHz when the antenna arms are fully extended. In other words, depending on your application (range, RF output power settings on transmitters, obstruction to line of sight between transmitters and receivers, etc.) the SNA600a may work for you over greater than 100MHz bandwidth. If you have any additional questions, please feel free to email me directly at nick.mariano@lectrosonics.com or call 800-821-1121 x171 or ask for Nick if reception picks up the call. Thank you, Nick Mariano Technical CSR Lectrosonics, Inc. nick.mariano@lectrosonics.com (800)-821-1121 x 171

Q: 7. I want to use this antenna for the VR Field, but do I need to choose all my transmitters to the same Block as this antenna for it to work?

A: This antenna is designed for devices operation in Block 22 only.

Q: 8. Do they just push-on (fall-off?) or are these heat-shrink?

A: The Lectrosonics Color Coded Transmitter Antenna Caps push onto the top of Lectrosonics' "AMM" style antennae and provide a snug fit that does not require heat shrink to secure. Once installed, these caps should not come off unless intentionally removed by the user.

Q: 9. Will this antenna fit the Shure P10Rplus PSM1000 Bodypack Receiver ?

A: The Shure UA700 is a replacement whip antenna for the Shure UR1 UHF body-pack transmitter.

Q: 10. I'd like to boost the range of my Lectro dualSRC (a1)Rx and (block 23) IFB Tx. Do you suggest multiple sna's ( one for each unit ) or would a splitter be optimal ?

A: Diversity receivers use 2 antennas, so for the SRc, best practice would be to use 2 for the receiver. As the SRc is not a true diversity receiver unless in ratio mode, it will not dramatically increase range in switch mode (the mode the SRc must be in to receive 2 channels). It's not recommended to use the same antenna for transmission and reception, so the IFB should be on a different antenna altogether.