Whirlwind Wp2/1Nl4 Wall Plate With Neutrik Nl4 Terminal

Whirlwind Wp2/1nl4 Wall Plate With Neutrik Nl4 Terminal

Product Code: eq32209
Availability: In Stock

$75.00 $98.25

Qty

12 reviews Write a review

Description
Reviews (12)

Finish your installation with a clean look with the stainless steel Whirlwind WP2/1NL4 2-Gang Wall Plate. It features a two-gang design with one Neutrik NL4 Speakon terminal to pass your wiring through the wall, reducing the appearance of cable clutter.

1x Neutrik NL4 Speakon Terminal 2-Gang Design

Parameters
Terminals	1 x Neutrik NL4 Speakon terminal
Gang Qty	2
Dimensions	Not specified by manufacturer
Weight	Not specified by manufacturer
Packaging Info
Package Weight	0.25 lb
Box Dimensions (LxWxH)	5 x 5 x 1"

Related Questions and Answers

Q: 1. Will this fit a matthews BabySitt'r?

A: No, the base plate of the Matthews Junior Wall Plate is too large to fit into the Matthews BabySitt'r.

Q: 2. can it be ceiling mounted?

A: As long as you have adequate support from above yes. I would look to anchor all four of the bolt holes into something very solid like a floor joist from the floor above. Be careful about finding a mounting surface that will provide adequate width so that you anchor all 4 corners using the provided holes. I would not bolt this to a drywall ceiling and attach anything weighing more than a few pounds to it. If you bolt this to the ceiling then you should also consider what you are going to attach to the pin and ensure that you can grip that pin firmly enough that it can hang upside-down with all of the weight trying to pull away form the pin.

Q: 3. How much weight can this hold?

A: I have used it up to 8 lbs, & to Secure it, I always suggest a Safety cable. Impact Safety Cable (18") BH #IMSC1.518 • MFR #SC-1815

Q: 4. Is the pin removable?

A: The pin is welded in place.

Q: 5. Can this be mounted on a standard light stand?

A: This Impact Wall Plate can only mount to a wall or ceiling and would accept a junior pin on top.

Q: 6. How big are the holes and what' the spacing? Was thinking of putting some magnets on this and want to get some ideas on sizes

A: The larger holes are 5mm, and the smaller 3mm. From center to center the large holes are 5.5 cm apart. From center to center the small holes are 3.5 cm apart. The entire plate is approximately 7.5cm x 14.5cm

Q: 7. What is the dimension from the back of the plate to the far end of the receiver?

A: It is about 3 inches from the back of this plate to the far end of the receiver.

Q: 8. what is the distance between the holes?

A: The large Outside holes are 6 centimeters by 13 centimeters on center. The small Inner holes are 4 centimeters by 12 centimeters on center.

Q: 9. Which hole is the "safety cable hole"?

A: safety cable goes on the Baby Pin

Q: 10. Can the handle be removed?

A: Yes the handle can be unscrewed.

heath	18/09/2024
[2] It is well made and does the job 5

Bill	01/09/2024
[2] Not using it as a wall plate. There are many uses instead. 1. by screwing a 12x12 board to the top, It mounts on any stand to support a laptop for those zoom calls on the set. 2. Again on top of any light stand, I taped a small Roland speaker to the top to enable audio for an event. I am sure to think of many other uses. 5

Mati	29/08/2024
[5 x 5 x 1"] nice 5

Patrick	24/08/2024
[5 x 5 x 1"] Fit this Neutrik NA3FDM XLR Female to Male Feedthrough Adapter for Panel Mount into a RapcoHorizon SP-1DFN XLR Single Gang Wall Plate with 1 Neutrik NC3FD-L-1 Connector after knocking out the rivets, then re-riveting it to the plate. Then I fit it into a movable pulpit where the original jack had been abused and the soldered connections severed. In a church environment, who can fix that, and who needs downtime? Especially with very young and active kids! 5