Finish your installation with a clean look with the black Whirlwind WP2B/1MW 2-Gang Wall Plate. It features a two-gang design with one Whirlwind WC3M male XLR terminal to pass your wiring through the wall, reducing the appearance of cable clutter.

1x Whirlwind WC3M Male XLR Terminal    2-Gang Design

Related Questions and Answers

Q: 1. Is this actually 12 channels or is it 8 like the picture? I ordered the 12 channel one in 50' but when it came it was only 8 channels.

A: Whirlwind Medusa Multitrack snakes are available as 4, 6, 8, 12, 16, 24 or 32 line configurations. Other channel counts are available as special orders. They are built with XLR, RCA jacks, or 1/4 TRS plugs. Each fanout can be specified with distinct connector types and signal polarity. When the same type of connector is specified at each end, wiring is pin to pin. Wire mesh hanger grips can be ordered as an option. If you received the wrong configuration, please contact your B&H sales representative to discuss this issue. The snake model number must be configured and then ordered for you.See details here: a href= http://www.whirlwindusa.com/catalog/snakes-splitters-and-multiwiring-systems/snakes/medusa-multitrack-audio-snake target= _blank www.whirlwindusa.com/catalog/snakes-splitters-and-multiwiring-systems/snakes/medusa-multitrack-audio-snake/aThank you.

Q: 2. Does the stated length (10') include the fan length, or is the male-xlr to female-xlr length 14' (assuming each fan is 2')?

A: Yes it includes the connectors total legnth

Q: 3. What are dimensions of the flat plate itself (not the receiver)?

A: The size of the plate is approximately 5.9x3.6".

Q: 4. What is the dimension from the back of the plate to the far end of the receiver?

A: It is about 3 inches from the back of this plate to the far end of the receiver.

Q: 5. What is the length of each segment -- that is, from an individual XLR plug to where it enters the four-cable bundle, and the segment where the four cables are bundled together? For instance, if the "fanned" portions were 2' each and the bundled portion were 10', it would be 14' from a male XLR plug to its matching female plug.

A: I just measured my cable, and each fan is approximately 2' and the bundled segment is about 6', so the total length (XLR male to XLR female) is the advertised 10'. You do not get a "bonus" 4' due to the two fans -- their length is included.

Q: 6. How long are the individual channel pigtails on each end of the bundled cable?

A: The distance from the start of the fan to the end is 2.5'.

Q: 7. Can this be mounted on a standard light stand?

A: This Impact Wall Plate can only mount to a wall or ceiling and would accept a junior pin on top.

Q: 8. Will this receive a full size C-stand riser?

A: Yes, the opening is 1 1/8 which is standard for most C stand columns.

Q: 9. We at our church are having trouble with our sound system. We have a Xenyx 1222FX Mixer and a Whirlwind Medusa 16x XLR send and 4x XLR return stage box. We have had some individuals mess with the set-up and do not have instructions to get it back functioning. What are the orange high-lighted inputs A, B, C, and D. What should be plugged into one or all of them? The octopus harness seems easy enough to figure out. If there is a user's manual for the Whirlwind, I sure would like to have one. Thanks, Clint

A: The return jacks on a snake generally connect to the outputs of a mixer either mains or monitor for connection to amps, powered monitor speakers or on occasion a headphone monitoring system.

Q: 10. what is the distance between the holes?

A: The large Outside holes are 6 centimeters by 13 centimeters on center. The small Inner holes are 4 centimeters by 12 centimeters on center.