The Da-Lite Flex Plex 58x104 In-Wall Projection Screenfrom Da-Lite Flex Plex 58x104 In-Wall Projection Screenis designed for applications that cannot accommodate a large crate. It can be used with one of nine standard coating options formulated to fit your application requirements. The Flex Plex is an acrylic, lightweight rear projection screen that ships in a roll. Coatings are permanently bonded to the substrate and cannot peel off.

Da-Lite Flex Plex 58x104 In-Wall Projection ScreenPlease specify the desired screen surface when ordering. For Wide-Angle (WA) surfaces, additional costs apply.

119" Diagonal / 16:9 Aspect Ratio    For Rear Projection    Acrylic, Lightweight Construction    Ships in a Roll    In-Wall Installation    Specify Coating When Ordering

Ships in a roll

Includes frame, mounting t-track, and trim

All surfaces can be cleaned with mild soap and water, and are flame-retardant and mildew-resistant

Related Questions and Answers

Q: 1. Can I use this adapter with a 1x2 flex mat

A: Unfortunately, no. The 1x2 has higher power requirements than the 1x1 so this cable will not work. Westcott say they are developing a mobile power solution for the 1x2, but I haven't seen any notice that they've released it. You can call Westcott support to inquire.

Q: 2. anyone use this shade on canon's 17tse?

A: I doubt it would work, since a wide angle lens would include it in the image. This for large lenses anyway.

Q: 3. It says in the description that it is a full stop but the review says 1/4 stop diffusion. Which is it?

A: Westcott lists that the Westcott Flex Cine Softbox 1 x 1' comes with a one stop front diffuser.

Q: 4. Does anyone know if you can use this cable to power the Bescor Flex 1X1 LED ?

A: Yes it does. It is titled Westcott Flex D-Tap Cable and is designed to connect the flexlight via D-Tap on batteries and distribution boxes.

Q: 5. I have two Flex light Cine Kits... One 1x1 and one 1x2. I have two D-Tap connectors (one for each). NEITHER cable works on either light. There's power to the 1x2 control unit, but will not light the light. There's no power to the 1x1 control unit. Ideas?? Thank you!

A: For color temperature of LEDs you would need the Sekonic C-700R Spectromaster or a spectrometer specifically designed to accurately read LED light. Other versions and older color meters simply are not designed to accurately measure the light output of LEDs. In addition, While the actual readout from a Flex LED may be different than the what your brand and model of camera records as a specific temperature, once set, your Flex will maintain the same color temperature each time you set it with the same readout. Your output range may be related to the D-tap question where you appear to be attempting to use powering options and connectors not specifically designed for use with your Flex. Please contact Westcott Customer Service if you experience issues beyond what I addressed as we stand behind our products and their performance.

Q: 6. Will this unit also ship with an Anton Bauer Gold Mount version?

A: No it will not.

Q: 7. Can the dc plug fit into a Video Device PIX-e7?

A: As far as I know, this is a proprietary plug for the Flex light.

Q: 8. Will the 2 ft flex yoke also work with the 1 x 3 slim Jim cine frame (used in the Westcott Peter Hurley LED light kit?)

A: Steven,Mounting the 1 x 3 requires the 1' version of the yoke.

Q: 9. rotation of top bar is which degree?

A: The top bar for this item BH #EAMINIMAX rotates approximately 120 degrees from left to right on center.

Q: 10. Can I use the Anton Bauer Cine battery to power the Flex 10 x 10 with this cable?

A: From our in-house engineer: Yes, as long as the output is between 13v and 29v it can power your 10 x 10 flex.