Designed for large venues, the 120V Da-Lite 29248 Wireline Advantage Motorized Projection Screenuses thin steel cables instead of black drop to lower the screen to an appropriate viewing height. Once the screen is installed, the screen's trim conceals the rough opening in your ceiling, eliminating the need to complete additional trim work. Sliding installation brackets help make it easy to attach the screen housing to the structure above the drop ceiling.

208" Diagonal / 16:10 Aspect Ratio    HD Progressive 1.3 Surface    1.3 Gain / 150° Viewing Angle    Suspended from Cable up to 29'    Slim-Tab, Low-Profile Tab-Tensioning    Hand-Held Remote Included    Built-In Radio-Frequency Motor    Seamless, Black-Backed Screen Surface

Ideal for applications where projector brightness and screen size require an increase in gain, the white surface offers high-fidelity color reproduction, and allows for more flexibility with ambient light conditions. This surface works for video as well as charts and graphs in a corporate setting. Cone 150° Gain: 1.3

• Up to 29' of cable to accommodate appropriate viewing height in rooms with high ceilings
• Slim-Tab, a lower profile and stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension
• UL Plenum-rated case
• Works with separately available radio-frequency control accessories such as a single-channel wall switch, dry contact interface, and RS-232 interface
• Black-backed screen material for enhanced image quality and opacity
• Seamless screen surface

Related Questions and Answers

Q: 1. does this fit on the GVM 60w cube light?

A: The GVM 36° Projection Kit was not designed to be used on the GVM 60W light. There is a compatibility list offered by GVM, and it states that this kit will only be compatible with GVM's PR150D, Pro SD200B, Pro SD300B, SD80D, SD300D, SD300S, SD200D, and SD200S models.

Q: 2. Will the gobo and iris slot accept standard B gobo holders and irises for an ETC Source 4?

A: No, the Arri Orbiter 25º Projection Optics is not interchangeable with gobo holders or irises used on the ETC Source 4 Ellipsoidal.

Q: 3. Dear All, how close to the back ground wall can it be placed? Thanks

A: How close this lens can be placed in relation to a background wall would be dependent on the type of lighting being used. For example, if this lens was used with one of the Dedolight DLH4 Tungsten Lights, that would produce a greater amount of heat versus using the lens with a Dedolight DLED4.1 LED Light.

Q: 4. CAN I USE THE Godox BLP LED Projection Attachment for Bowens on the Godox AD600Pro Witstro All-in-One Outdoor Flash?

A: Yes, the Godox BLP LED Projection Attachment for Bowens is compatible with the Godox AD600Pro Witstro All-in-One Outdoor Flash.

Q: 5. Can I attach it to DLH4 light head directly? Do I need any other accessories for using it?

A: It attaches directly to the front of the HLH4 housing; just ahead of the filter slot, and is locked in by the same rotating top clip that locks the filter in place.

Q: 6. Will this work on any of the Profoto heads?

A: This lens can only fit on a Profoto Multi-Spot Flash Head.

Q: 7. Will this fit the DLED4.1 head?

A: Yes it will.

Q: 8. Will this work with aputure units? Will it work with 600x/d/c?

A: The Godox BLP LED Projection Attachment for Bowens BH #GOBLP is designed for Bowens mount LED lights under 300w.

Q: 9. Will this fit on the DLED 2.1 as well? Their videos show a DP1s is this the same?

A: The B&H page that describes the DLED 2.1, in the Acessories section, lists the DPS1 as the recommended imager for the DLED 2.1.I use the MDLH4 with the DP 1.1 imager and the 85 mm 2.8 lens. As far as I can tell there are only single versions of the lenses for all their imagers, which makes perfect sense.Alternatively, if you have a Leitz slide projector, the Leitz projector lens will fit BUT without the safe travel groove on the lens AND with the danger of an indent mark on the lens if over tightened.The imager and lens combination works really well. I also use the iris diaphgram attachment to control the light spread - it all works beautifully well with my macro projects.(The iris control lever has quality issues - it is loosely glued rather than screwed in - and should never be used to remove the diaphgram from the imager. Instead, loosen the attachment tightening screw on the imager and push from the bottom. This is not in any Dedo information.)

Q: 10. I would like to find a similar projector to fit elinchrom 600w studio lights. Ideally with optional metal leaves to control the area to be lighted. Does anyone have any recommendations?

A: Please review the following item. https://bhpho.to/3pEq4Us