The Cinegears Pegasus Cable Cam Bodyfrom Cinegears Pegasus Cable Cam Bodyis the core of the Pegasus high-payload cable cam system. Add the necessary controller, wheels, mounting plates, and other components, all sold separately, and mount cameras or entire gimbal setups up to 17.5 lb. The Pegasus can be used as a cable cam as well as a dolly on flat surfaces, remotely controlled in both modes. The Pegasus supports up to two cables, one on each side, or you can loop just one around to serve as two cables supporting the same 17.5 lb. The maximum travel speed is 25" per second in cable mode and 39" in dolly mode. The maximum incline in cable mode is 35°. The maximum control range is 0.62 miles (3280') and there's no limit to the length of the cable that you can use. Multiple controllers can be synced to the same Pegasus unit. In dolly mode, the travel route can be programmed in various ways, including at an arc angle.

The Pegasus is designed with a highly responsive ultrasonic safety mechanism. Collision sensors trigger a complete stop instantly upon detection of physical interference along the travel path.

The Pegasus comes with a V-mount battery plate with a D-Tap port attached on top. It also features three onboard LEMO ports: a large 12-18 VDC, 8A input and two standard-size 12-18 VDC, 3.5A outputs. Between the D-Tap and LEMO ports, the Pegasus offers the flexibility to power most or all of your accompanying gear.

Works as Cable Cam System and as a Dolly    17.5 lb Payload    25" per Second Max Travel Speed    35° Max Incline    Responsive Collision Detection Sensors    V-Mount Plate with D-Tap Port    2-Pin LEMO Input/Output Ports

• 17.5 lb payload
• Works as a cable cam system and as a dolly (optional components required)
• 25" per second max travel speed in cable mode
• 39" per second max travel speed in dolly mode
• 35° maximum incline
• Ultrasonic safety mechanism / highly responsive collision detection sensors
• Stainless steel and aluminum construction
• V-mount plate with D-Tap port
• 2-pin LEMO input/output ports

Related Questions and Answers

Q: 1. how fast is the motion?

A: The Genie can move at a maximum speed of 3.84 cm (1.51 inches)/ 1 second and can cover a distance of 100cm (or 3.3ft) in around 25 seconds.

Q: 2. Will this work with the URSA Mini?

A: The Ursa Mini cameras have a standard 2.5mm LANC input. We believe that this Trigger Cable should work with the Ursa Mini.

Q: 3. Does this lanc port work with the fx6 or fs7? It says c300 & c500 and "select cameras".

A: It also works with Sony PXW-FS7 / PXW-FX9.

Q: 4. Can this be set up to "ping-pong" between two points indefinitely? Or only a set amount of times?

A: The CINEGEARS Pegasus Wireless Cable Cam Kit has the "Set Cycle times" setting that would allow you to repeat the program many times in succession. It does look like it would be only a set number of times. PG 10 https://www.bhphotovideo.com/lit_files/452180.pdf

Q: 5. Is this wired pin 1 +VDC? Or is it pin 2?

A: We are not aware of such a version of this cable. So that we may best assist you finding the proper product for your needs feel free to email us directly at askbh@bhphoto.com.

Q: 6. Does this provide power to the cforce mini RF motor as well?

A: It does not. This cable enables camera run/stop, camera status display, and tally functions via an ARRI or cmotion cPRO electronic-control hand unit. It is not a power cable.

Q: 7. can this unit move fast or is it only for time-lapses?

A: This can do standard dolly shots for video. It is not limited to just time lapses.

Q: 8. Does this cable work with Sony Burano?

A: ARRI does not state compatibility of the ARRI Cable CAM (7p) to LANC/D-Tap (2') with the Sony BURANO 8K Digital Motion Picture Camera, but considering the compatibility to other Sony cameras and the presence of a 2.5mm LANC input, it should work.

Q: 9. dose this work with the Syrp Genie II Motorized Pan/Tilt Head ?

A: Yes, the Syrp Genie II motorized pan/tilt head can be used with the Slingshot.

Q: 10. I use a setup of one hard wired remote along with a splitter cable and extension cable to trigger two cameras at the same time for interviews so they do not require syncing in post and for the volume of interviews that I do this setup is very important to me. I used two 5DmarkIII's before and now use one 5DmarkIII with my new C300markII. Will this or any other known remote trigger both of these cameras with one remote using a splitter cable? I tried with two intervalometers I currently have and they do not trigger the C300markII even with remote setting correctly set to standard mode unless there's something else I'm missing. Thanks for your help!!!

A: I'm sorry to say we are not aware of a solution like this that will work for both the C300 Mark II and the 5D Mark III. The C300 Mark II and 5D Mark III have different connections for remote controls, which makes this not possible.