The Avenger Butterfly Pipe Corner Kit contains corners and supports that will give you the ability to make frames in desired sizes using standard lengths of 1.5" aluminum pipe. Note: pipe purchased separately.

Do-It-Yourself Frame Kit    Uses Optional 1.5" Pipe

Related Questions and Answers

Q: 1. Are the threads etched on to the outside of the pipe or does this come with threaded connectors?

A: the pipes have a thread cut inside, then they machined nipples with 2 male threads on them to join the tubes. you keep the nipple mounted on one side, and there is a protective rubber cap for when not in use.they are awesome for when you need to be moving around location, rather than dragging long pipe around.the threads are a little fine, be careful getting them started so you don't strip them.

Q: 2. How much does this item weight?

A: The Impact Pipe Clamp weighs 1.37 lb (0.62 kg).

Q: 3. Does this tubing kit work with the Dana Dolly Universal System? My question is because in the specifications of this kit of tubes it says that it has a diameter of 1.25 "/ 3.17 cm and for the Dana Dolly Universal System to work they recommend tubes of Outside Diameter: 1.5 to 1.9 "(3.8 to 4.8 cm). Can someone explain to me if they have used it and if it is correct what I explain? I would not like to buy it and that it is not tight and loose.

A: Dana Dolly make two types of track ends, the “Original” which only works with 1.25” speedrail (pipe has an O.D. of 1.66”, I don’t know where they get the 1.25” BTW) and the “Universal” which works with any size pipe from 1.25” to 1.5” (again, the pipe size does not correlate to the actual size of the pipe for some reason). The pipe kit is made from schedule 80 aluminum pipe that is 1.25” (the 1.66” O.D.) and it works with both track ends. It is a little confusing because of the fact that the actual measurements don’t correlate with what the pipe is named, but we’ve found on the West Coast people generally use the 1.25” speedrail or aluminum pipe for grip trucks, and on the East Coast the 1.5” pipe is the most common size. The Universal track ends are also the ones anyone outside of the USA will want to use. Hard to find the proper size in say, Romania.

Q: 4. Can I use it with the Proaim Polaris Dolly and also are there curves trails for this purpose ?

A: This set is for the Dana Dolly and would also work with the Proaim Polaris dolly. We are not aware of a curved option.

Q: 5. What clamp do you recommend to attach to a stand-mounted grip head for a C-Stand?

A: Please consider the following to adapt to any c-stand Impact Grip Head for Lights and Accessories - 2.5" Diameter (Chrome) BH #IMKCP200 • MFR #KCP-200 https://bhpho.to/3xReGb4 Impact 6" End Jaw Vise Grip BH #IMME106 • MFR #ME-106 https://bhpho.to/2E9r8Z8

Q: 6. How long is each pipe? What is the total maximum length of the assembled track?

A: This kit comes with six 39" lengths of schedule 80 aluminum pipe. That would give you 117 inches for each side of the dolly track, which is just a bit under 10 feet of length.

Q: 7. How do the pipes connect? Are they threaded on both ends?

A: Yes they are threaded on both ends - male on one end and female on the other. Great kit BTW, and you get real personal service from the owner at Dana Dolly.

Q: 8. Can you combine two kits to get 18' of track?

A: Yes, you can combine two kits.

Q: 9. can the universal track ends hold these pipes?

A: Yes, because the Dana Dolly Portable Aluminum Pipe Kit is made and compatible with the Dana Dolly Universal Track Ends.

Q: 10. What diameter pipe is this rated for? "Schedule 40" is a rating for the thickness, not the diameter.

A: 1 & 1/8 ( junior pin size )