The Custom Hard Case for ARRI FF-5 Follow Focus Custom Hard Case by Jason Casesis designed to transport and protect your ARRI FF-5 follow focus. The case is constructed by fitting a hard-shell Pelican 1500 case with a foam interior precision-cut to snugly hold all the FF-5 components. You have the option of storing the FF-5 with the right knob attached and ready to go, or storing it separately if you usually work without it.

The case is waterproof, crushproof, dustproof, and chemical-resistant. It features a replaceable neoprene O-ring for waterproofing, and has an automatic purge valve that equalizes the air pressure inside the case in sync with atmospheric changes. The large top handle pivots flat when not in use for streamlined storage. The Pelican 1500 case also features easy-to-open but secure double throw latches. Stainless steel inserts bolster the strength of the two padlock holders.

Holds All FF-5 Components    Dedicated Laser-Cut Foam Interior    Pelican 1500 Case    Watertight, Dustproof, and Crushproof    Stores FF-5 with or without Right Knob    Large Folding Top Handle    Stainless Steel Padlock Inserts    Built-In Purge Valve

• 1 x ARRI FF-5 Base (with 15mm/19mm bridge plate)
• 1 x Right side knob
• 1 x Left side knob
• 1 x Speed crank
• 1 x Long focus whip (12")
• 5 x Marking disks
• 1 x Module gear (0.8mm)

Laser-cut foam interior cradles each component

Has slots to store the FF-5 with or without the right focus knob attached

Unbreakable, watertight Pelican 1500 case

Replaceable O-ring

Built-in purge valve for atmospheric changes

Large, folding top handle

Stainless steel padlock inserts provide added security

Related Questions and Answers

Q: 1. Will this case take C200 with to handle or will I need to take top handle out every time before I close the case

A: The top handle will fit attached

Q: 2. Will this fit the sunhood too?

A: We're afraid not. According to Jason Cases this case fits the SmallHD 13″ 1303 Monitor, SmallHD Monitor handle (attached), C-stand monitor mount (attached), Acrylic screen protector (optional) and Cables only.

Q: 3. Can one leave the lens on (24-105L). Are there cutouts for lenses?

A: More than likely you will need to remove the 24-105mm lens for the C200 to properly fit in this case. However the 2 spots in the upper left hand corner for for lenses.

Q: 4. Will this work with the new broadcast g2 camera?

A: No, the Jason Cases Hard Case with Custom Foam for Blackmagic Design URSA Camera (Red Overlay) is specifically designed for compatibility with the Blackmagic Design URSA 4.6K EF-Mount, Blackmagic Design URSA 4.6K PL-Mount, Blackmagic Design URSA 4K EF-Mount, and the Blackmagic Design URSA 4K PL-Mount.

Q: 5. Can you just purchase the cutout?

A: No. Following unit is made of custom lab foam inserts.

Q: 6. Can this be brought in carry-on?

A: Check with your airline's carry-on policy. Most airlines can accommodate a 24-inch carry-on, but not all. Generally, a carry-on suitcase measuring 22 inches x 14 inches x 9 inches, commonly seen as 22 x 14 x 9, would be the most widely accepted size. This case is 24.76 x 19.57 x 13.90" / 62.9 x 49.7 x 35.3 cm, so most likely, it would need to be checked.

Q: 7. Can you reverse the Follow Focus rotation? (Clockwise/Counter Clockwise)

A: According to Tilta, you cannot reverse the follow focus rotation on the FF-T03.

Q: 8. Will this fit the Cine13?

A: At this time, the case we are recommending for the SmallHD Cine 13 UHD 4K High-Bright Monitor is the Innerspace Cases Case for SmallHD Cine 13 4K High-Bright Monitor with Foam Insert in Pelican Air.BH #IN901871 • MFR #9018-71.

Q: 9. Is the actual case a Pelican?

A: Yes it is. This is made with genuine Pelican case.

Q: 10. Can you use this with 19mm rods?

A: Hello,Unfortunately, no. If you need something for 19mm rails, I recommend either the FF-T05-v2 or, to get fancy, the PDL-F from PD Movie.