The GyroVu 120 LED Panel for DJI Ronin-M MX MoVIfrom GyroVu 120 LED Panel for DJI Ronin-M MX MoVIcan provide up to a 450-lumen output and a horizontal lightning angle of up to 60°. Using the rear control buttons, the light intensity can be adjusted easily. Each light comes with two L-Series type NP-F550 lithium-ion batteries, a portable charger, and two filters (diffusion and 3500K). The LED Light Panel can mount on any 25mm rod or round pipe, and rests on a 4mm carbon fiber plate. It is designed for the DJI Ronin-M/MX and Freefly MoVI stabilizers (not included).

LED Light Panel with 450-Lumen Output    Can Mount on Any 25mm Rod/Round Pipe    Two Filters Included

Compatible with the DJI Ronin-M/MX and Freefly MoVI stabilizers

Related Questions and Answers

Q: 1. Will this work with the Ronin RS2?

A: It will not.

Q: 2. What comes with this? Is it just a shim or is it the armstand mount and 25mm brackets too?

A: The images are incorrect. You will get the shim only. We apologize for the confusion and inconvenience. Here are the correct images. https://bit.ly/2IJoU1Z

Q: 3. is it ok to be mount on Ronin-M Horizontal Bars?

A: Yes, you can use this mount as well as the one seen below on the Ronin-M.Please note back/special order status for both items.

Q: 4. Will this work with the DJI Ronin-M?

A: The GyroVu uses 25mm bars and so does the DJI Ronin-M so we do not see why this would not work. Just know this has not be tested.Here are two other GyroVu mounts you might consider.

Q: 5. What sizes are the allen wrenches?

A: The sizes of the allen wrenches on the DJI Multi-Tool for Ronin-SC, Ronin-2, Ronin-S, Ronin-MX, Ronin-M & Ronin are 5mm, 4mm, 3mm, 2.5mm, 2mm, 5/16" and 3/16", which are the appropriate sizes for DJI gimbals.

Q: 6. Is mounting it to the Ronin M relatively quick and easy, tool-less? How does it lock in place after sliding on?

A: Mounting will be quick and easy. It does have screws on it though, that way you can adjust the Monitor Mount and hold it securely in place after it is installed.

Q: 7. Does this for a 30mm handlebar?

A: This is for a 25mm handlebar

Q: 8. The glidecam x-10 has a 21.5mm pin. The description includes the X-10 but the nearest listed sizes are 7/8" and 3/4" (22.22mm and 19mm respectively). Can you confirm if this adapter comes with a shim for a 21.5mm pin or is the 7/8" close enough to work without slop/wobble?

A: No, the GyroVu Universal DJI Ronin-M/MX to Vest Arm Post Adapter does not come with a shim. We have the Glidecam X-10 Dual Support Arm Stabilizer Vest System listed as using a 5/8" Junior pin for mounting.

Q: 9. Hello! I just bought one of these. I can't seem to figure out how to get the ball head to stand still, its always loose. Is there a way to tighten it up?

A: you should be able to make it stay still by tightening BOTH red pieces

Q: 10. Lost my Ronin top bar + handle, can this replace it ?

A: That may be possible, however this product is designed specifically to allow you to mount a Ronin on to an Arm and Vest System such as those that are used with Steadicam products. The DJI Grip for Ronin, B&H # DJRP52G, would be a more appropriate replacement option.https://bhpho.to/2xCiGyd