The IK Multimedia T-RackS EQ PB - Preamp & EQ Plug-In Downloadfrom IK Multimedia T-RackS EQ PB - Preamp & EQ Plug-In Downloadis a plug-in based on the equalizer implemented on many custom designed modular consoles of the late '60s and '70s. Its four-band proportional Q design has been meticulously modeled, including the entire custom op amp-based circuitry. Seven frequency centers per band make repeatability very easy, and their selection allows for extremely musical results.

Each band has 1 dB gain-resolution, becoming 1.5 dB in the higher part of the knob throw. The four band design is particularly useful for treating midrange-critical tracks, like guitars, vocals, pianos, or strings. Having two midrange-dedicated bands that span from 75 Hz to 12.5 kHz with some overlapping, allows the EQ to perform a variety of boosts and cuts for enhanced shaping of tracks. The low and high bands can be switched to shelving mode for broader strokes if required.

The proportional Q design and EQ curves are closely matched so that the boost or cut is broader at lower amounts of gain, and sharper as the level increases. This results in minimized phase shifting with no additional controls needed for bandwidth management. Additionally, engaging the module's preamp and boosting its gain makes all components from the filters network to the output transformer react differently, expanding the sonic possibilities. When the preamp is disengaged the gain and out controls act as clean input and output levels to the EQ section.

4-Band Proportional Q Design    Preamp Section    7 x Frequency Centers per Band    Low/High Bands Switchable to Shelf    Standalone    AAX Native, Audio Units, RTAS, VST    Mac OS X, Windows

Classic American 4-band EQ-preamp plug-in for DAWs

Works within the T-RackS CS Standalone application

High-quality oversampling

High-precision and high-transparency digital processors

Accurately analog-modeled vintage classic devices

Full-latency compensation support

Supports sampling rates up to 192 kHz

Native compatibility with 64-bit applications and operating systems

Related Questions and Answers

Q: 1. Will this controller work with the SkyWatcher Virtuoso?

A: Unfortunately no. It is not compatible. Sincerely, Garret at Celestron

Q: 2. Will this work for a Celestron CGE Eq mount?

A: Yes it should work.

Q: 3. Will this tracker work in the Southern Hemisphere?

A: I have not taken is south of the equator yet, but yes, it has a setting for the southern hemisphere and the polar alignment scope has the ring for Sigma Octanis to do a polar alignment in the southern hemisphere.

Q: 4. How long it the cord?

A: The IK Multimedia iRig Mic has a permanently attached 2m/6.5 ft. cable.

Q: 5. I'm interested to hear from anyone who used this during the solar eclipse. Would you recommend this?Thank you,Mike

A: This was fantastic during the eclipse. I made very little adjustments aftet setup. I used my remote and enjoyed the show. I've also tracked stars for over 5 min with pinpoint accuracy.

Q: 6. When will I be able to use this mic with an iPhone 6 or 6S?

A: Immediately. It plugs into the headphone jack and works like any other mic or headset.

Q: 7. Is it compatible with mounting celestron advanced cg5 gt?

A: It works with my CG-5 mount, which I purchased in 2003.

Q: 8. will this one will work with nexstar 60SLT ?

A: No, the Celestron NexStar+ EQ Hand Controller is only for EQ mounts, and can only be used with the Celestron NexStar 60 SLT 2.4"/60mm Refractor Telescope Kit if one flashes the firmware for the AZ mounts. A better option is to get the Celestron NexStar+ AZ Hand Controller, BH #CENSHCUA (https://bhpho.to/3K5P93F).

Q: 9. Will this work with an iMac?

A: It will work with many Macs, but not all. If you have a pair of earbuds with a built-in microphone, you can use these to test if your Mac will work, as these use the same wiring scheme as iRig Mic.

Q: 10. will this work with a celestron Nexstar 11 gps (2004 model year) ?

A: You will need the NexStar+ Hand Control USB, AZ, Item #:93981.