The HIGHWIRE Powerstar QUAD - Veracityfrom HIGHWIRE Powerstar QUAD - Veracityworks with the HIGHWIRE Powerstar base side (available separately) to deliver PoE to up to four network cameras over RG59, RG6, or RG11 cable. The camera unit receives PoE power from the base unit and transmits it to the connected cameras. No external power cabling is required, and all detection and setup occurs automatically.

This unit features SafeView to provide a quick confirmation of correct operation from either end of the cable. The low-power design enables long range extension even over low-grade cable, such as high-resistance copper-clad steel (CCS) types. Reliable power delivery is also ensured at the source, where either screw-terminal connections or a UPS-backed PoE supply can be used. It delivers a full 200 Mbps of bandwidth at up to 1000' of RG59, 1148' of RG6, or 1600' of RG11 coax cable.

Transmits PoE to Up to 4 Network Cameras    Supports PoE and Non-PoE IP Cameras    Provides 10-78W of PoE, 25W Max Per Port    SafeView Connection and Power Status    10Base-T/100Base-TX Ethernet Support    Compatible with RG59, RG6, & RG11 Cable

Delivers power to up to four network cameras

PoE eliminates the need for additional cable runs

Delivers up to 25W of PoE per port, between 10-78W total power

SafeView quickly indicates connection and power status

Works with the HIGHWIRE Powerstar base side (available separately)

Related Questions and Answers

Q: 1. How does IP addressing work? Does the unit pull 4 IPs from my network or reuse 1? I am trying to determine if I will end up with a quad-display inside one of the camera zone's on my NVR.

A: All this unit does is convert the Ethernet signal to work over coax, your router will still provide each device with an IP address. You will still need the VHW-HWPS-C​ to make this work properly.

Q: 2. The photo doesn't show it, but I would assume the power cord comes with it?

A: The AC power cable is included

Q: 3. This will supply POE power to cameras located 800 feet away?

A: If you are speaking about the distance from the VHW-HWPS-C4 to the cameras, then we are looking at 100 meters which is the ethernet standard. However, the distance between the VHW-HWPS-B and the VHW-HWPS-C4 is 300 meters.

Q: 4. does the rack mount chassis come with the unit?

A: Yes, the rack mount ears do come with the unit that allows you to mount the unit.

Q: 5. does it converts sdi to hdmi and hdmi to sdi?

A: The Accsoon CineView Quad Multi-Spectrum Wireless Video Transmission System (B&H# ACCVQUAD) allows for inputting to either type of video interface (either HDMI or SDI) on the transmitter and then outputting to the same or the other type of video interface (either HDMI or SDI) from the receiver.

Q: 6. To reach a distance of 500 ft (Cat 6 Cable PoE from NVR to Camera), do I need one PoE Extender in the middle only?

A: Yes you can put one of these in the middle of the run, just remember this model is not weather proof.

Q: 7. Will this help boost video/audio signal over cat6 as well?

A: The Veracity OUTREACH Max G Gigabit Ethernet & POE Extender is primarily used for extended power and data signals; it would also ensure the signal would offer the highest quality transmission for long cable runs.

Q: 8. How many watts of POE power does this support?

A: The Veracity OUTREACH Max G Gigabit Ethernet & PoE Extender (BH # VEVORORMG) supports up to 90W of power onto an Ethernet cable while maintaining backwards compatibility with older IEEE PoE standards.

Q: 9. I need to extend my network runs, possibly twice (resulting in 3 segments). The devices will not handle POE. Would the Outreach Lite work for this application or is there a better solution available?

A: This will allow you to extend your signal 3 times if needed but does not send POE.

Q: 10. Does the unit come with a power supply already or is that separate?

A: The Veracity HIGHWIRE Powerstar QUAD does not come with a power supply. A 57V power supply is separate.