Enhance your smartphone photography with the SHILL Smartphone Mount with Two 1/4"-20 Threads. This mount has 1/4"-20 standard tripod threaded holes on its bottom and back, enabling you to position your device in a variety of ways.

Dual 1/4"-20 Threaded Tripod Holes

Related Questions and Answers

Q: 1. does this unit have any tilting ability?

A: Is does have tilting ability, but I found this adapter to be shaken and had to modify it to make is stable. The base is spring-loaded to allow it to rotate. You pull it up and can rotate is in 90 degree increments. This spring allow the base to vibrate easily. I removed the spring and replaced it with a small metric (4mm, in thing) lock washer from Fastenal. This disables the rotation and direction of tilt, but since I use it from my GoPro, I have to use the GoPro mount which can be rotated in an direction and allows me to tilt it in any direction.In addition I lock the adapter so the built-in tilt is 90 degrees to the handle bar mount. This allows for two-axis tilting.

Q: 2. What is the diameter (in mm) of these tubes?

A: Each individual part from the RigWheels 6" Stand-Offs with 1/4"-20 Threads (Set of 4) (B&H# RISO14X64PC) is 6" (about 15.2cm) long and about 2/3" (16.7mm) in diameter.

Q: 3. Will this stretch far enough for a iphone 7+ (with small case) to fit?

A: Hello AdamThank you for your question! Our unit will indeed stretch far enough to fit with your Iphone 7+ if your case is not too thick. Our unit stretches approximately to 3 1/4 inches. Make sure your Iphone with the cage is within those dimensions.We hope this helps and we thank you for your interest in our products.The SHAPE team

Q: 4. Any idea what the load weight limit is?

A: Shill does not list a load capacity, however this product is designed for Action Cameras like the GoPro. GoPro's tend to only weight a few ounces in general, the load capacity will be in this range. If you seek a more robust solution the Delkin Devices Fat Gecko Dual-Suction Camera Mount has an 8 pound load capacity. https://bhpho.to/2gvteVy

Q: 5. Will this allow me to install a light mount, specifically a Godox S2, onto a standard tripod which has a QR plate with 1/4 x 20 threads?

A: Yes.

Q: 6. Can this clamp onto something as small in diameter as 15mm rods? Want something I could attach to shoulder rig to control GH4 through app.

A: It is not designed to work with anything less than 22 mm.

Q: 7. I'd like to try this with a Tascam DR-05 recorder. The recorder is light, but only 2 inches wide. Does this clamp close enough to hold that?

A: David, the clamp doesn't close it will only stretch open. Hope this helps. It is a good adapter for my iPhone 7 Plus.

Q: 8. Will my Avenger D600 boom sit securely on the 3.5" Impact Double Ended Spigot with 5/8" Stud and 1/4"-20 Threads?

A: Yes, the Impact Double Ended Spigot can insert into the stand mount of the Avenger D600 boom, as long as there is a secure connection below it.

Q: 9. Does it have cold shoe mount?

A: The SHILL Smartphone Mount with Two 1/4"-20 Threads BH #SHGP260 does not have a cold shoe mount.

Q: 10. Can I use this as a VESA for a laptop mount tray, and connect the VESA to a 1/4 boom arm? In Little words, can I use this as a adaptor for a laptop mount tray connected to a boom arm?

A: The VESA Compatibility on this CAMVATE Multifunction Cheese Plate with 1/4"-20 and 3/8"-16 Threads would be 75 mm.