Blue Cat Audio Destructor - Distortion & Amp Simulation Pluginfrom Blue Cat Audio Destructor - Distortion & Amp Simulation Pluginis a distortion and amp simulation plug-in that performs multiple functions. The software is capable of simulating any kind of distortion, from harsh digital destruction, to smooth compression or guitar amp simulation.

Distortion Modeling    Guitar Amp Simulation    Analog Compression    Non-Linear Tone Shaping    Bit Crushing    Tape Saturation    AAX Native, RTAS    Audio Units, DirectX, VST    Mac, Windows

• Distortion and amp modeling tool

• Simulate any kind of distortion - analog or digital, guitar and bass amps, saturation, clipping, compression, bit crushing, and more

• Works for "clean" sounds

• Several hundred fully editable presets, inspired by physical gear

• More than 1,400 visual styles to customize the user experience

• Control dynamics with the input gate and compressor

• Control the tone with the pre and post filters

• Exclusive shape dynamics control - adapt the tone to the dynamics of the signal

• Use the internal or external side chain to trigger the distortion

• Output brickwall limiter

• Comprehensive visual feedback - real-time spectrum analysis, and dynamic distortion curve display with embedded signal histograms

• Load reference curves for tone matching

• No latency

• Native DSP code for optimal performance

• Full MIDI control and automation support with silent, zipper-free parameters update, advanced response control, and MIDI Learn

• No CPU load on idle

• Skin-able and customizable user interface with transparency management

• Smooth bypass activates/deactivates the plug-in with no noise

• Undo/redo

• Full featured integrated presets manager

• Copy/paste the state of the plug-in between instances using the system clipboard

• Any sample rate supported

Related Questions and Answers

Q: 1. How long are you cables? Does this device have problems when using USB extension cables? Are the cables detachable? If the cables are detachable, what is the "device side connection"?

A: Hello, the cables are 2m (6.6 ft) and are built into the joystick and throttle bodies, so they are not detachable. You should be fine with a USB extension, as it only uses USB 2.0. If you are using a USB hub, it needs to be a powered hub.

Q: 2. What power supply would work best with the Zen Dac Signature?

A: ZEN DAC is powered by 5 volts, either via the enclosed USB cable or DC power supply. Either option would be fine.

Q: 3. Does this include a 5 volt power source as recommended in the manual?

A: No, the iFi audio ZEN Air Blue Bluetooth Audio Receiver would not include a 5 volt power source.

Q: 4. How long are the pig tails?

A: The four XLR tails are approximately 24" long.

Q: 5. I would think you need 2 of these units send and receive ?

A: Depending on the application, you may need both male and female versions of the SoundTools CAT Tails MX Four XLR Male Audio Lines Down Shielded Cat 5/6/7 Cable. For instance, if you use this cable to send an analog signal over Cat cable and the device at the receiving end needs to make analog XLR connections.

Q: 6. Does this work with Xbox Series S console?

A: The Logitech G G X56 H.O.T.A.S RGB Throttle & Stick Simulation Controller is listed as compatible with only PC titles.

Q: 7. Can I connect this amp dac directly to my TV (LG C2 OLED)? I'm using the 42" TV as a monitor and also use it for my PS5

A: The iFi audio Zen DAC V2 USB DAC and Headphone Amp BH #IF0311002 will not connect to the TV.

Q: 8. Can I access a copy of the manual?

A: The Manual for this Logitech G X52 H.O.T.A.S Throttle and Stick Simulation Controller would be on the right side, under the what's in the box section

Q: 9. Does it work with FS2020?

A: The Logitech G G X56 H.O.T.A.S RGB Throttle & Stick Simulation Controller is compatible with Microsoft Flight Simulator, but some users have reported issues with calibration and support does not seem to be complete.

Q: 10. What is the input power Range of this unit?

A: It is 120 VAC 60Hz only.