Designed for large venues, the 120V Da-Lite 29458 Wireline Advantage Motorized Projection Screenuses thin steel cables instead of black drop to lower the screen to an appropriate viewing height. Once the screen is installed, the screen's trim conceals the rough opening in your ceiling, eliminating the need to complete additional trim work. Sliding installation brackets help make it easy to attach the screen housing to the structure above the drop ceiling.

137" Diagonal / 16:10 Aspect Ratio    Dual Vision Surface    0.9 Gain / 130° Viewing Angle    Suspended from Cable up to 29'    Slim-Tab, Low-Profile Tab-Tensioning    Hand-Held Remote Included    Built-In Radio-Frequency Motor    Seamless, Black-Backed Screen Surface

Dual Vision is a flexible vinyl surface ideal for rear projection, but capable of front projection as well. Dual Vision is ideal for video projection under controlled ambient light conditions. With a wide viewing cone and light gray tint, a sharp image with no color shift is observed regardless of location in the room. Cone: 130° Gain: 0.9

• Up to 29' of cable to accommodate appropriate viewing height in rooms with high ceilings
• Slim-Tab, a lower profile and stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension
• UL Plenum-rated case
• Works with separately available radio-frequency control accessories such as a single-channel wall switch, dry contact interface, and RS-232 interface
• Seamless screen surface

Related Questions and Answers

Q: 1. Will the gobo and iris slot accept standard B gobo holders and irises for an ETC Source 4?

A: No, the Arri Orbiter 25º Projection Optics is not interchangeable with gobo holders or irises used on the ETC Source 4 Ellipsoidal.

Q: 2. What's the difference between the DP1 and the DP1.1 ?

A: The DP 1.1 is an updated version of the DP1 which now has a double lens system and is optimized for use with the DLED lamp heads. This system would help increase the light output and offer better optical performance.

Q: 3. Can it be used with a bowens mount adapter?

A: This projector is designed to work with a Dedolight. It will not work with a Bowens mount.

Q: 4. Is this compatible with LED lights? If it is, what is the maximum power output LED light which it can handle?

A: The Godox BFP Flash Projection Attachment for Bowens BH #GOBFP was designed for studio flash.

Q: 5. Will this fit the DLED4.1 head?

A: Yes it will.

Q: 6. Does this attach directly to the ad400 pro?

A: The Godox BFP Flash Projection Attachment for Bowens has a Bowen-S connector. You can connect this light modifier to the Godox AD400Pro Witstro All-in-One Outdoor Flash with the Bowens Mount Adapter Ring included in the box with the flash.

Q: 7. Will this work on any of the Profoto heads?

A: This lens can only fit on a Profoto Multi-Spot Flash Head.

Q: 8. Does this work with elinchrom lights?

A: No, the Dedolight Projection Attachment with 85mm f/2.8 Lens is not compatible for use with Elinchrom light fixtures. While not identical, the Elinchrom Zoom Spot Attachment, B&H # ELZSAQ, would be a similar item that works with all Elinchrom monolight fixtures and may also use gobos. It allows you to focus the light, but it will have a hard edge to the light.

Q: 9. Would this work well on a Profoto B10 light with a bowens to Profoto adapter?

A: Godox BFP Flash Projection Attachment for Bowens will work with the GTX STUDIO Bowens to Profoto Flash Head Adapter.

Q: 10. Will this work with aputure units? Will it work with 600x/d/c?

A: The Godox BLP LED Projection Attachment for Bowens BH #GOBLP is designed for Bowens mount LED lights under 300w.