Da-Lite 29451 Wireline Advantage 78X139 Motorized Screen 120V

Da-lite 29451 Wireline Advantage 78x139 Motorized Screen 120v

Product Code: eq38522
Availability: In Stock

$89,778.00 $141,849.24

Qty

5 reviews Write a review

Description
Reviews (5)

Designed for large venues, the 120V Da-Lite 29451 Wireline Advantage 78x139 Motorized Screen 120Vuses thin steel cables instead of black drop to lower the screen to an appropriate viewing height. Once the screen is installed, the screen's trim conceals the rough opening in your ceiling, eliminating the need to complete additional trim work. Sliding installation brackets help make it easy to attach the screen housing to the structure above the drop ceiling.

159" Diagonal / 16:9 Aspect Ratio Dual Vision Surface 0.9 Gain / 130° Viewing Angle Suspended from Cable up to 29' Slim-Tab, Low-Profile Tab-Tensioning Hand-Held Remote Included Built-In Radio-Frequency Motor Seamless, Black-Backed Screen Surface

Key Specs
Front/Rear Projection	Front and Rear
Aspect Ratio	16:9
Diagonal	159.0" / 403.9 cm
Gain	0.9
Tensioned	Yes
Type
Series	WirelineAdvantage
Front/Rear Projection	Front and Rear
Aspect Ratio	16:9
Style	Wall and Ceiling
Dimensions
Viewing Area	78.0 x 139.0" / 198.1 x 353.1 cm
Diagonal	159.0" / 403.9 cm
Surface
Finish Name	Dual Vision
Gain	0.9
Viewing Angle	130 degrees
Tensioned	Yes
Black Backing	No
Controls
Motor	Standard
Included Controls	No
General
Voltage	120 VAC/60 Hz

Dual Vision is a flexible vinyl surface ideal for rear projection, but capable of front projection as well. Dual Vision is ideal for video projection under controlled ambient light conditions. With a wide viewing cone and light gray tint, a sharp image with no color shift is observed regardless of location in the room. Cone: 130° Gain: 0.9

Up to 29' of cable to accommodate appropriate viewing height in rooms with high ceilings
Slim-Tab, a lower profile and stronger tab design to keep your screen taut
Tensioning Cable System to prevent warping and ensure even lateral tension
UL Plenum-rated case
Works with separately available radio-frequency control accessories such as a single-channel wall switch, dry contact interface, and RS-232 interface
Seamless screen surface

Related Questions and Answers

Q: 1. What are the bulbs dimenions?

A: The Ushio ECT Photoflood (500W/120V) is; Maximum Overall Length (MOL) 5.98" / 152 mm Maximum Overall Diameter (MOD) 3.12" / 79.38 mm

Q: 2. Do these bulbs contain mercury. Product page says it "may contain Mercury"?

A: I contacted the manufacturer concerning your inquiry. According to Ushio, they state that the Ushio JCD 300W Lamp (300W/120V) GY9.5 does not contain mercury.

Q: 3. Is this the correct replacement bulb for Smith Victor? It came with Sylvania (2) 500 Watt bulbs and a 250 Watt bulb.

A: Yes.I use them in my Smith Victors

Q: 4. Will this bulb work with a Leitz Focomat Iic enlarger?

A: No, the Kaiser Opal Lamp (75W, 120V) is not correct. If you are in the USA any of these can work, https://bhpho.to/3HORVIP .

Q: 5. Will this work for the Profoto D1?

A: Yes this Ushio DRA is compatible with the Profoto D1.

Q: 6. Is the Impact ELH lamp ok for use in a Kodak Carousel 760H Projector. If not, what lamp would you recommend?

A: From all I have found on the internet, the ELH lamp is suitable for the Kodak 750, 760, 860 projectors. I bought this bulb for an 860H and it works just fine. Hope this helps.

Q: 7. Can you put this 500w bulb into a 420w Pepper light?

A: Although this 500 watt bulb can fit, it is not recommended for use with the LTM Pepper 420. A more suitable bulb is the Ushio EKB Lamp - 420 watts/120 volts, B&H # USEKB. https://bhpho.to/395yPN1

Q: 8. what is the dimension (inch) of the bulb?

A: around 1.75

Q: 9. Is the color produced by this bulb orange or white?

A: The color temperature of the EMD lamp is 3200k, which means that it is tungsten-balanced rather than daylight-balanced.

Q: 10. I need four.

A: Buy Four if you need four! i have several spares because i drop them and knock my light stand over.

Gab Laughin	13/07/2024
[Front and Rear] We installed this in a rehabbed church space that's now a contemporary art gallery flush mounted it to an exposed beam and it looks and works great. That said, it's only been about a week, so maybe I'll report back later if I have any complaints! I was surprised that, for its length, there are only 2 mounting holes on either end, so I fear that it may sag over time. But again, too soon to tell. Where it does mount in those 2 places, it's on a solid plastic end cap/brace, so it seems like it will hold up well. It weighs about 85 pounds, so we had 3 people to install. We had to go about 17 feet up to the beam, we leveled, marked and pre-drilled & drove lag bolts into the beam and then used two extension ladders on either side to climb and carefully slide the projector up on the ladder's rails. Our 3rd person was on a 10ft ladder in the middle and was there as a spotter for extra support. It was then quite easy to hook it on to the lag bolts once we slid it to the top. All in all, it's an easy install, we opened the box and had the job done in less than 4 hours. Just be sure you have the wiring supplies and the proper mounting hardware and you'll have no problem! 5

Chip	17/06/2024
[Front and Rear] We use the screen in our church sanctuary once or twice a month. Installing it was an adventure with the weight and length, but several sections of scaffolding and a couple friends made the install move along nicely. The instructions for wiring were right on and it worked first try! The image is right on and visible the entire length of our viewing area (over 100'). 5

Zack	25/05/2024
[Front and Rear] I installed in my living room in between ceiling joists. It works great. I use it with a Panasonic HD projector. It impresses everyone who walks in the room. Has a clean appearance when retracted. Note: it didn't come with a 12v trigger as both the B&H customer service rep and myself thought it did. We both misunderstood the description (it's optional.) The part was available at Da-Lite for $80 and came with no instructions. I got it to work after a few emails and chats with da-lite. Also, I ended up placing some holes in the top of the case to mount using 8 Lag bolts into the 2nd story floor structure. All the hardware that comes with it assumes you will have access to hang it from the top which requires access via the side while it's in it's final position. I was putting it in a hole the size of the case in my finished ceiling so that method would not work ( I would have had to remove and re-install a lot of drywall). I knew this before I purchased by reading the installation instructions so no worries just a fact and maybe a consideration for future changes to the case or just the directions. 5

S_Kim	06/05/2024
[130 degrees] I have used this Da-Lite screen for the past 3+ years. This is actually my second purchase. Compared to some brands and products, the price is reasonable. The design is solid, great for portable use and easy to setup. However, it weights close to 70 pounds. A great product nonetheless. 5

haze_1	07/04/2024
[130 degrees] I use it in a classroom at a university. It's got a great surface, brilliant white, big and more than I expected. It looks like a big LCD screen on the wall, way cool. 5