Designed for large venues, the 120V Da-Lite 29452 Wireline Advantage Motorized Projection Screen 92x164uses thin steel cables instead of black drop to lower the screen to an appropriate viewing height. Once the screen is installed, the screen's trim conceals the rough opening in your ceiling, eliminating the need to complete additional trim work. Sliding installation brackets help make it easy to attach the screen housing to the structure above the drop ceiling.

188" Diagonal / 16:9 Aspect Ratio    Dual Vision Surface    0.9 Gain / 130° Viewing Angle    Suspended from Cable up to 29'    Slim-Tab, Low-Profile Tab-Tensioning    Hand-Held Remote Included    Built-In Radio-Frequency Motor    Seamless, Black-Backed Screen Surface

Dual Vision is a flexible vinyl surface ideal for rear projection, but capable of front projection as well. Dual Vision is ideal for video projection under controlled ambient light conditions. With a wide viewing cone and light gray tint, a sharp image with no color shift is observed regardless of location in the room. Cone: 130° Gain: 0.9

• Up to 29' of cable to accommodate appropriate viewing height in rooms with high ceilings
• Slim-Tab, a lower profile and stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension
• UL Plenum-rated case
• Works with separately available radio-frequency control accessories such as a single-channel wall switch, dry contact interface, and RS-232 interface
• Seamless screen surface

Related Questions and Answers

Q: 1. Can I attach it to DLH4 light head directly? Do I need any other accessories for using it?

A: It attaches directly to the front of the HLH4 housing; just ahead of the filter slot, and is locked in by the same rotating top clip that locks the filter in place.

Q: 2. Is the speed ring interchangeable? If so, what size is it?

A: The speedring that is part of the Godox BFP Flash Projection Attachment for Bowens is not interchangeable.

Q: 3. What is the focal length of the included lens?

A: The Godox BFP Flash Projection Attachment for Bowens comes with an 85mm lens.

Q: 4. Will this fit the DLED4.1 head?

A: Yes it will.

Q: 5. CAN I USE THE Godox BLP LED Projection Attachment for Bowens on the Godox AD600Pro Witstro All-in-One Outdoor Flash?

A: Yes, the Godox BLP LED Projection Attachment for Bowens is compatible with the Godox AD600Pro Witstro All-in-One Outdoor Flash.

Q: 6. does this fit on the GVM 60w cube light?

A: The GVM 36° Projection Kit was not designed to be used on the GVM 60W light. There is a compatibility list offered by GVM, and it states that this kit will only be compatible with GVM's PR150D, Pro SD200B, Pro SD300B, SD80D, SD300D, SD300S, SD200D, and SD200S models.

Q: 7. Does this work with elinchrom lights?

A: No, the Dedolight Projection Attachment with 85mm f/2.8 Lens is not compatible for use with Elinchrom light fixtures. While not identical, the Elinchrom Zoom Spot Attachment, B&H # ELZSAQ, would be a similar item that works with all Elinchrom monolight fixtures and may also use gobos. It allows you to focus the light, but it will have a hard edge to the light.

Q: 8. Will this work on any of the Profoto heads?

A: This lens can only fit on a Profoto Multi-Spot Flash Head.

Q: 9. Would this work well on a Profoto B10 light with a bowens to Profoto adapter?

A: Godox BFP Flash Projection Attachment for Bowens will work with the GTX STUDIO Bowens to Profoto Flash Head Adapter.

Q: 10. Can it be used with a bowens mount adapter?

A: This projector is designed to work with a Dedolight. It will not work with a Bowens mount.