Arri Clm-5 Motor Controller Cable

Product Code: eq38984
Availability: In Stock

$420.00 $663.60

Qty

15 reviews Write a review

Description
Reviews (15)

Use this ARRI CLM-5 Motor Controller Cablefrom ARRI CLM-5 Motor Controller Cableto connect the motor to an ARRI UCM-4 or SMC-1 motor controller.

Connects CLM-5 Motor to Controller For UCM-4 & SMC-1 Controllers

Parameters
Connectors	Not specified by manufacturer
Length	Not specified by manufacturer

Related Questions and Answers

Q: 1. Can this also be used to power the nucleus handle?

A: Yes, you can use this cable to power the Nucleus-M handle. To do so safely, make sure you remove any batteries from the handle.

Q: 2. Will this work on an Arri Alexa Plus?

A: yes it will work with the Alexa Plus

Q: 3. The length says 1' but does it include the connector parts or is it only for the cable part?

A: The total length of the ARRI LBUS cable( end to end) is 30cm or 1ft

Q: 4. How much power output is needed to power the cable and motor through a Sony NPF battery adapter? My adapter drops 7.4v power and I wanted to know if it is correct to power the Nucleus M motor.

A: The Nucleus M motor supports Voltage 7.2-24 V

Q: 5. How do I power the item and does the cable come with this unit?

A: It is powered by the LBUS. It does not come with the cable.

Q: 6. Hi, can we do the lens mapping with the SMC 1 as well as the UMC4 ? Thanks

A: Yes, you can perform lens mapping with the ARRI SMC-1 and UMC-4.

Q: 7. Can I use this cable with CAMVATE V-Lock Mounting Plate Power Supply Splitter with 15mm Rod Clamp B&H#CAC1524 Mfr#C1524 ?

A: Yes, you can use this cable with the Camvate plate.

Q: 8. Hi, is this one support lens data like UMC-4? and is it possible to connect Cforce motor via LCS/CBUS cable?

A: The ARRI SMC-1 Single Motor Controller does not support lens data similarly to the UMC-4. You can only connect to a cforce motor via the CLM port.

Q: 9. Do these motor cables work with Motr.X and MDR.X?

A: All we know for sure is that the Teradek RT Latitude MDR Motor Cable (8", RA to RA) is compatible with the Latitude MDR and the MK3.1 receivers.

Q: 10. I have a RED DSMC2 with Tilta's C1 cage, which has a 7 pin connector that has MOTOR written on it. If I plug this cable into it, will it provide power and camera communication (REC start/stop) to my Nucleus M system?

A: No this will not work for Run stop controll of the camera this is used to connect a Nucleus-M 7-Pin Motor to Motor Cable from Tilta to connect one Nucleus-M lens control motor to another.

Trevor	17/09/2024
A 1' LBUS cable is just about the perfect length for me. I often mount my motors from the top of the camera, so a 1' cable reached from the LBUS port on the lens mount up to a top-mounted motor just perfectly. If using more than one motor, I try to place them on either side of the lens in order to balance the weight for my operator, and again the 1' cable is the perfect size to reach across the lens to the other motor. 5

Murad	09/09/2024
use easy. have not any problem 5

Joshua	08/09/2024
I find the Nucleus - M calibrates better at the lower voltage even with the torque set to the lowest setting. I found the Nucleus - M tried too hard at the stop points at 12volts and would not actually calibrate correctly. 5

Mar	06/09/2024
The cables are sturdy and you are comfortable knowing that you wont loose connection 5

Clifford	04/09/2024
I priced having this cable costume made to save some money but I couldn’t find a vendor that could do it. But if you have two motors it is worth having to lessen the cables on your camera. 5

justin	02/09/2024
Love this whole set-up. It's incredibly useful and this cable to work with it all is no exception. 5

anyonymous	01/09/2024
LO PROBE EN EL MOTOR Y NO TUVE NINGUN PROBLEMA! 5

anyonymous	28/08/2024
It works perfectly 5

Mary	27/08/2024
Small and very lightweight. Easy to calibrate, but sometimes have to remove battery to re-calibrate. The thin controller that goes with is brilliant. And on/off switch would help. It’s tricky to figure out to push the battery to the side. 5