Plug SD, HD, or 3G-SDI sources into consumer displays or projectors with the Osprey SHC-2 SDI to HDMI Mini Converter. Incoming video signals up to 1080p60 will be passed through to the HDMI and SDI loop outputs without scaling or other processing. Minimal processing ensures that the converters remain small and unobtrusive, while allowing more advanced devices to perform image control in the SDI signal domain. a USB power supply is included as well as mounting brackets.

Supports up to 1080p60 Resolution    HDMI Output with SDI Passthrough    No Scaling Performed    Small Form Factor    USB Power Supply

Related Questions and Answers

Q: 1. Can it be powered by the mini usb port?

A: No, requires 12 volt power.

Q: 2. Could I use this device to convert the 8 bit 4.2.2 HDMI data coming out of the Sony a6300 to be recorded in my Oddesy 7Q, which only has 3G SDI input?

A: Yes, that should work.

Q: 3. Will this output to both HDMI and SDI at the same time? I am looking to record a computer's feed to an AJA IO4k via SDI while also passing the feed through to a projector via HDMI.

A: Simultaneous output through HDMI and SDI is possible.

Q: 4. Can I leave this unit plugged in?

A: Most of the racks that we install for clients are left on, but plugged into a battery backup/surge protector.

Q: 5. Does this work with Sony FS700, SDI 3G out, 12 bit out ?

A: It handles both 6G and 3G SDI. We use it with our 3G video equipment to use cheaper HDMI projectors, so it should work with your 3G camera, but we don't have that model to say for certain.

Q: 6. Will this allow me to rotate a video source 90 degrees?

A: Yes, the AJA ROI HDMI to SDI Mini Converter offers 90-degree rotation on the output.

Q: 7. Does anyone know of a mounting brackett compatible with this Aja ROI HDMI unit? I need to mount it to a monitor.

A: The AJA mount for the AJA ROI HDMI to SDI Mini Converter is the following part listed below: AJA RMB-RO Rackmount Bracket BH #AJRMB • MFR #RMB

Q: 8. does it convert 1080p to 4k?

A: No, this device does not convert 1080P to 4K.....4K is 4 times the resolution of 1080P (think 4 1080P signals combined). This device takes a video signal on an HDMI cable and converts it to an SDI cable. Why convert to an SDI cable? Because SDI cables can carry a video signal MUCH further than an HDMI cable can a video signal. What kind of input signals can this device handle and convert to SDI? It can handle video resolutions of 4K, 1080P and lower. But all it s does is convert the input signal from HDMI cable to SDI cable, it does not change the input resolution.....what goes in is what goes out....just over a different kind of cable that can handle longer distances than HDMI can handle. If you want to convert a signal from one resolution to another.....like 1080P to 4K or the reverse 4K to 1080P then you need a video scalar like this product from B and H......SC-HDM-HD42K 2-Port HDMI 4K Scaler from Avenview.

Q: 9. I am wanting to connect a 2013 iMac to a ATEM Television Studio Pro 4K. Would this Converter work if I used Mini DisplayPort to HDMI from the iMac, to the HDMI in on this Converter, and then passed SDI to the Switcher?

A: Hi, I don't have the switcher, but I do have the Blackmagic HDMI-SDI 6g, and an atomos shogun inferno, and a 2012 MacMini. I was able to see output from the Mac Mini at 1080p, but did not see any choices for higher resolution. I'm not sure that you can even pass 4:2:0 2160 signal at 30fps over a 3g input Blackmagic does make an admittedly more expensive HDMI - SDI convert to pass full UHD, BH #BLTRMHDMISDI • MFR #CONVNTRM/AB/HSDI (the Blackmagic Design Teranex Mini HDMI to SDI 12G Converter). I'm not a B&H employee, but they have a very reasonable return policy; you could ask if they wuold let you try the cheaper one, and if it didn't work, exchange it with more $$ for the faster one.

Q: 10. Can this unit allow for color tweaking in the ATEM Control Software with the ATEM Mini?

A: No it does not pass the necessary data from SDI to HDMI.