Maintain an orderly equipment rack in your studio or OB truck with the 1 RU Custom 16-Port BNC Feed-Thru Patch Panel 1 RUfrom My Custom Shop. Designed to facilitate troubleshooting, this panel is a key component of a complex network, sparing you a severe headache and precious time when the system goes down.

The recessed build protects the BNC connectors, and the black powder-coated finish is resistant to corrosion. This patch panel is designed and crafted in the USA by My Custom Shop from high-quality components to fit your budgetary and technical needs.

16 x Connectronics 75-Ohm BNC Connectors    Easy I/O Patching    Connectronics Straight-Thru Connectors    Protective Recessed Connector Design    1 RU Configuration    Corrosion-Resistant Coated Finish    Assembled from High-Quality Components    Solution to Disorganized Cable Array    Simplify Cable Troubleshooting Protocol    Made in the USA

Route signals between cameras, recorders, and CCUs in an organized fashion. Maintain order within your studio, OB truck, or production rack.

Connectronics "Straight-Thru" 75-ohm connectors enable easy I/O patching. The panel's protective recessed design and corrosion-resistant durable black powder-coated finish help extend the longevity of your equipment.

Related Questions and Answers

Q: 1. Is the finish painted or powder coated?

A: Not positive it's powder coated but it looks very similar to a more expensive panel I have that is powder coated. Good value!

Q: 2. Is this backward compatible with Cat 5e cables?

A: They are backwards compatible, but the cables rating may have other affects on your data performance.

Q: 3. What size screws do the front port holes use for adapators? I bought TecNec SCREW-38B 4-40 x 3/8" Flat Heads, but they too small

A: The My Custom Shop 16-Port Unloaded Rackmount Panel with Rear Lacing Bar (1 RU) does not have threaded mounting holes, so you will need to use a nut with your screws. The recommended screw is SCREW-38B and the corresponding nut would be the NUT-CMT.

Q: 4. would this work with 3G/6G/12G Sdi inputs without quality dropping? would i lose the audio signal that comes embeded?

A: This Technec Patchbay is Composite Video only, it will not accept an SDI signal of any kind. We do have some 3G-SDI Patchbays available that you could look in to. For a 4k signal passed through 6G-SDI we have the Blackmagic Design Smart Videohub 12x12. Blackmagic also makes a 40x40 Smarthub that accepts a 12G-SDI signal. Audio will be embedded through any of these solutions.

Q: 5. Does the Tentacle Sync Tentacle to BNC Cable (Straight, 16 ) work with the BMD HyperDesk Mini single one directional RF BNC Input?

A: The Tentacle Sync (C06) BNC TC cable is designed for bi-directional use. Being that you are looking to send timecode out, and into the BMD HyperDesk Mini, I would recommend a one directional TC/OUT cable from ambient; B&H# AMBNC3.5.

Q: 6. Could I use this to jam sync a tentacle from my c200 timecode out sdi connection?

A: This cable will only work to jam sync if the camera has the capability to do timecode.

Q: 7. how deep is this rack cover? ie. how far can the knobs on the equipment stick out and this unit still fits over top?

A: The depth of the ProX T-P2SEC 2U Security Rack Panel is 1 inch.

Q: 8. Will this fit the thread spacing on the bottom of the Decimator MD-HX?

A: This My Custom Shop shelf is a universal solution and should allow you to attach any small converter model to the shelf.

Q: 9. is it work with 1080P ?

A: Yes, the TecNec 8-Port HDMI Feed-Through Patch Bay (1 RU) V1.3 HDMI ports can support up to 1080p@60Hz signals.

Q: 10. What screws can I use to mount connectors?

A: You can use 4-40 x 3/8" or 4-40 x 1/2" screws with the TecNec 16-Port Unloaded D-Series XLR Rack Panel (1 RU).