This GyroVu 7" Articulated Arm Mount Adjustable Clamp Quick Releasecomes with a jaw clamp and a two-part quick release attachment. The top plate of the quick release screws onto your monitor via a 1/4"-20 interface, and you can then quickly attach or remove your monitor, releasing it at the pull of a slide button. You can also mount LED lights and other devices. The jaw clamp can grip onto gimbal tubes, tripod legs, table edges, and other objects matching its clamping range of 0.5 to 1.5". It's secured by a T-handle and is rubber-padded to prevent twisting and scratching.

The articulating arm is 7" long fully extended and has a native 1/4"-20 stud on each end, to which the clamp and quick release secure. The center mechanism uses rosettes for locking the arm, preventing slipping due to wear or insufficient tightening. A wingnut in the center tightens all three joints of the arm at the same time.

Two-Part Quick Release    Top Plate Attachment to Your Monitor    Jaw Clamp for Tube/Pipe Mounting    Attach to Gimbal Tubes/Tripod Legs    Clamping Range of 0.5 to 1.5"    Rosette Center Lock

Related Questions and Answers

Q: 1. What is the maximum length of this fully extended and the individual length of each arm?

A: Fully extended it is about a 6 length. The two arms are about 3 .

Q: 2. Will this work on a crane weight bar?

A: Yes 100 %. The following unit offers a clamping range of 0.5 to 1.5"

Q: 3. What is the max capacity that this arm can hold? Would a EOS R with a 35 mm Sigma lens be too heavy?

A: A load capacity for this arm is not listed. However it is really designed for accessories only and we do not recommend it with a camera the size of the EOS R. The Impact 3 Section Double Articulated Arm with Camera Bracket, BH #IMBHE119K, and a Impact Clamp would be a much better choice, BH #IMCC106R. https://bhpho.to/3oYTlGM https://bhpho.to/2Y8DWbb

Q: 4. would this fit on a Schatler ACE xl?

A: Yes it will. You will be able to clamp this product to the Ace XL Tripod System.

Q: 5. Will this arm support a mirrorless camera (i.e. Sony A6500) ?

A: The Magic Arm is rated for 5 lb load. The clamp, depending or the position can handle up to 2-4 points. We we think it will support Sony A6500. Sincerely, GyroVu Team

Q: 6. Will this attach to a tripod leg and other end hold 7 inch field monitor? Also will monitor be adjustable ( tilt up and down)?Thank you

A: Yes, this will attach to most tripod legs. The principle advantage of articulating arms is that they are completely flexible. So yes, you will be able to place the monitor in any position.

Q: 7. would this 11" arm be good for mounting a Godox M1 (B&H # GOM1) to something like an oben Table top tripod (BH #OBTT100)? I don't want to use something ridiculously large like a full blown cstand/lightstand/camera tripod to mount a 1/2 lb godox M1 unit, but would like more angle and height versatility, that presumably a 11" arm would give. But not sure if it's a wise way to get there, if the 11" arm would be too top heavy for the oben tabletop tripod/tip over, etc. I would be looking to use it in vehicle interiors and behind subjects of a greenscreen to create separation. I find having the tabletop pod on the floor or on a carseat isnt verstatile enough (light looks too underlit and unnatural) and don't have places to clamp the godox m1 inside a car without damaging cars i don't own, etc. And similarly, the angle of the light for backlighting a subject to create separation w a greenscreen isn't high off the ground enough to get an effective wrap around a seated subject, if am just using the tripod on the floor. Plus it would be great to be able to angle the light to fine tune a greenscreen key, etc.

A: The Manfrotto 209 Tabletop Tripod (BH #MA209), would be more suitable to support the Gyrovu Heavy-Duty Articulated Arm (11-), as it has a much higher load capacity. You may also want to consider a small sandbag for further reaches of the arm with the Godox M1 light. https://bhpho.to/3CWx6en

Q: 8. Can you remove the shoe mount to have 1/4-20 at each end?

A: Yes, the hot shoe mount can be unscrewed.

Q: 9. I’m looking to find an articulated arm that will hold the monitor for the c200 when in the Crane 3s - would I be able to make something like this work?

A: yes this would work as long as it's clamped to the handle or the gimbal

Q: 10. Does this unit include the screw to mount to a camera bottom?

A: Yes