The Lectrosonics M2TND IEM Transmitter 470-608 MHzfrom Lectrosonics M2TND IEM Transmitter 470-608 MHzfeatures transmission power up to 50 mW for extended operating range and locking XLR/TRS combo connectors, that facilitate up to four channels of analog audio sources. With ultra-low latency, 24-bit audio, and two stereo-digital channels, the M2T is an IEM transmitter for professional broadcast applications.

Built with a USB port for firmware updates and an IR port for fast setups, the M2T transmitter has a large, high-resolution backlit color LCD with large membrane switches for an intuitive interface visible in daylight or dimly-lit conditions. Analog signals are converted to an internal 24-bit digital format that is encoded, organized into packets, and passed to an RF modulator. The RF signal is filtered before and after amplification to suppress out-of-band noise and spurious signals.

Additionally, the M2T transmitter employs a technology that provides a frequency response from 20 Hz to 15 kHz with maximum channel separation. This digital audio technology eliminates a compandor and the associated artifacts, resulting in crystal clear sound, rock-solid stereo imaging, and low distortion.

IEM Wireless Monitor with Digital RF    24-Bit Digital Audio    USB Port for Firmware Updates    Analog Inputs    IR (Infrared) Port for Fast Setup    Up to 50 mW per RF Carrier    All Metal Housing    Works with Wireless Designer Software

Related Questions and Answers

Q: 1. in terms of heat dissipation, is it safe to operate this inside a K-Tek Stingray audio bag for IFB?

A: Yes it is safe to operate the Sennheiser SR IEM G4 Stereo Transmitter inside of an audio bag for IFB.

Q: 2. Am I able to use the lectrosonics IFB to tune into this transmitter? I didn't see an IFB mode.. just DHCT and DUET mode.

A: This unit is not compatible with the IFB model receivers. For an IFB receiver, you'd need a version of their IFBT4 transmitters in the corresponding frequency as the receiver. Such as this B&H # LEIFBT421.

Q: 3. It is possible to combine a Lectrosonics L-Series LMb (B1: 537 to 614 MHz) with a UCR 411A?

A: Yes, the LMb transmitter can be used with all Lectrosonics Digital Hybrid Wireless receivers including the UCR411a when the compatibility mode for the transmitter and receiver are both set to the "Nu Hybrid" compatibility mode. Lectrosonics notes that if your receiver does not have Nu Hybrid mode, then set the receiver to the "Euro Digital Hybrid Wireless" compatibility mode.

Q: 4. What is the expected runtime for the SMDWB on Eneloop Pro 2450s and Energizer Lithium (the data sheet only shows Alkaline, which seems possibly incorrect)?

A: The battery run time for the Lectrosonics SMDWB with AA lithium, disposable batteries is. At 50 mW (2 x AA): 14.5 hours and at 100 mW (2 x AA): 14 hours.

Q: 5. Does this Transmitter have IFB mode to use as an IFB Transmitter?

A: Yes, the Lectrosonics L Series LT Bodypack Wireless Transmitter does have an IFB mode option in the compatibility settings.

Q: 6. Is there a battery eliminator made for this?

A: No,at this time there are no battery eliminators or alternate powering options available for the LMb transmitter.

Q: 7. Hi guys, I would like to know if these transmitters came with the Lectrosonics SMDWBBCSL Spring-Loaded Metal Belt Clip Kit (Antenna Up or Down) or I have to buy them separated. Thanks for the support

A: Please call customer service at 800-821-1121

Q: 8. Is there a way to assign left channel to one receiver and right channel to another, either through the transmitter or the receiver configuration settings?

A: Unfortunately not , channels are not assignable.

Q: 9. What frequencies does this transmit on?

A: The Sennheiser SR 2050 (A+) transmits on 470 MHz to 558 MHz.

Q: 10. Does the transmitter come with a belt clip included?

A: The Lectrosonics LMb Digital Hybrid Wireless Beltpack Transmitter does come with a metal belt clip.