The Avenger E600C Snap In Pin has a hexagonal end that snaps into a Super Clamp or similar grip accessory. The other end will accept a lighting fixture that has a 5/8" female receiver. It is fabricated from chrome-plated steel.

Chrome-Plated Steel Construction    5/8" Hex and 5/8" Pin    For Super Clamps

Related Questions and Answers

Q: 1. Can the 40 arm hold a Mola Setti and Strobe?

A: Hi Sean,I use the 40 arm to hold a 22 Mola Demi on an Einstein strobe. The Avenger stand and arms are built like tanks, so I unless your strobe weighs a ton, I can't imagine the arm or clamp would be challenged. Don't forget sandbags for the base if the arm is extended. Best regards.

Q: 2. How do you attach this to a Westcott 6.5 Boom Arm? The pin on the Boom Arm is not long enough and is not interchangeable... Any ideas?

A: To mount this adapter onto a Westcott boom, you can use the Manfrotto 153 Mole Richardson Baby Adapter - 5/8-5/8 B&H # MA153 which will help you have a better fit by lengthening the pin. Please see the image for reference.

Q: 3. Are there any casters for this stand?

A: Tether Tools makes a caster stand that I use with this C stand. You can place a sand bag right in the center of the caster stand for stability.

Q: 4. What transport case is recommended for these since the legs don't detach?

A: C stands with permanent legs not a turtle base are an issue for travel. The stand is about about 53 inches x 22 inches. B&H does not carry a case that large. The C stands with legs that come off are much smaller in the width. Those types give you some case options.

Q: 5. Can I located the stands on stairs ?? I'm not sure if this could be possible thanks.

A: No. We suggest c-stands with sliding legs. Please review the following item Savage 40" Riser C-Stand with Sliding Leg (Black, 9.6') BH #SACB600 • MFR #CB-600 https://bhpho.to/3BHsDcD

Q: 6. How much weight can this hold? Do you think it can suspend properly a Westcott Zeppelin 47 with the Bowens mounting bracket, the focusing rod, a Bowens speed ring and a Phottix Indra500 TTL?

A: It's not quite as simple an answer as you may like. It depends on how you angle the pivoted extension. If it's angled down a 90 degree angle and a lightbox is simply hung from the spigot, then it should support pretty well any modifier and light. But if you angle a heavy modifier beyond 90 degrees down and therefore have to rely on the friction/clamping of the two small wing nuts, you may find it frustrating, ie. difficult to hold a position. Hand tightening the wing nuts probably won't create enough grip on the spigot and you'd probably have to use a wrench or pliers to add leverage to the tightening. I bought this drop down pin for, as the name implies, it's ability to drop down a light modifier and simply hang it on the spigot. If you keep to that use, or use it with a light weight modifier/light combo which should be ok to angle at other than 90 degrees, then you should be fine. I hope this helps.

Q: 7. is this the model with sliding legs?

A: Not sure I follow you, but the three legs turn to point in the same direction to carry more easily.

Q: 8. What adapter do I need with this c-stand to use with an Alien Bee 800?

A: You need this stud , Avenger E650 6.0" Pin with Collar B&H # AVE650

Q: 9. Is the Avenger E600C Snap In Pin long enough to connect to a Super Clamp and then attach the Avenger D250 Gag Gobo Grip Head?

A: Yes the Avenger E600C is long enough to attach to a Super Clamp and then attach to the Avenger D250 Gag Gobo Grip Head.

Q: 10. What's the closed length, will this fit in a bag with 48 interior?

A: Hi JamesThe closed length is 49 but you can unscrew and remove the counterweight hook on the end which brings the length to 47 . That's how I carry it. Hope this answer helps.